SLUDGE LEVEL PROBE TAKES CONTROL OF DRINKING WATER CLARIFIERS
Drinking water treatment plants face the ongoing challenge of optimising the effi ciency of their processes to adapt to new
water quality regulations. The transposition to Council Directive 98/83/EC limits the permitted concentration of polyacrylamides used as a fl occulant in the settling process.
A plant in southern Europe with a treatment capacity of 1.5 m3
had two lamella clarifi ers for the treatment of purge water and water used for fi lter backwashing, sending the sludge directly to a centrifuge. There were two centrifuges that ran almost continuously and use polyacrylamides as fl occulants.
The purging of the clarifi er was conducted using time-based cycles adjusted periodically by the operator. This often resulted in highly variable purged sludge: there were periods where a high concentration of solids created mechanical problems that required the clarifi er to be emptied, and other periods where the drawn-off sludge was highly diluted, making the dehydration process very ineffi cient.
/s
Hach’s Sonatax sludge level probe was proposed to automate the removal of sludge from the clarifi ers. This probe uses an ultrasonic pulse to determine the sludge level from the water surface or the sludge height from the tank fl oor. The fi rst issue to be resolved was the location of the probe, which requires a space with no obstacles along its vertical to correctly determine the level. The probe was situated over the clarifi er’s sludge collection hopper, where the settled sludge is at its highest level. Despite being located over the sludge collection mechanism, probe measurements are not altered when working with sludge levels higher than the sludge scrapers. The Sonatax probe is programmed to also determine shadow areas that prevent interference from obstacles situated at known heights in the tank.
The measurement obtained was used to determine when to start sludge removal periods. The duration of these removal periods was time-based. The system was tested to determine how it functioned with both polyacrylamide-based fl occulants and starch- based fl occulants. The starch produced a less dense fl oc, which creates turbulence in the sludge removal process that can cause measurement errors in the Hach Sonatax probe. To prevent this, it was determined that, once the purge had started, based on the level indicated by the Sonatax, the programmed purge time would start. An inhibition period would then be maintained, which would enable the turbulence generated during the purge process to be eliminated. The programmed sequence involved one minute of purging and fi ve minutes of inhibition. The purge time needs to be adjusted for each clarifi er based on the conditions of the process.
Conclusion
The Hach Sonatax sludge level probe enables the sludge removal cycle in lamella clarifi ers to be automated, thereby achieving optimum sludge concentration results at the centrifuge inlet. These optimum results are achieved with different electrolytes by adjusting the sludge level at the start of the purge, based on the fl oc density obtained. Starch produces a lighter fl oc and the sludge level needs to be kept lower than when using polyelectrolytes to prevent the sludge from lifting under high hydraulic loads. Both types of fl occulant signifi cantly improve the stability of the removed sludge, with an increase in the concentration of solids.
Sludge dryness based on the flocculant used and the sludge purging system % sludge
concentration with polyelectrolytes
Automatic purges 3.35% Time-based purges 2.26%
% sludge
concentration with starch
2.62% 0.99%
Thanks to automatic purging control, the settling process adapts to the hydraulic load, thereby preventing the accumulation of solids around the plates and thus reducing the amount of maintenance needed. The increased concentration of the drawn-off sludge enables a 50% reduction in the centrifuge operating time. This makes expansion of the dehydration system unnecessary when changing the type of fl occulant and signifi cantly reduces the energy consumption of the current centrifuges.
Sonatax sc probe Sonatax sc probe over sludge collection hopper.
Author Details José Carlos Merino, Process Support, Hach Lange
Contact Details Mira Kovacheva, Vertical Marketing Manager Drinking Water HACH LANGE GmbH Email:
mira.kovacheva@hach.com
José Carlos Merino
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64