Table 1. Different Aging/Machinability Scenario Observed in Gray Cast Iron Scenario 1
Gray Iron 2 3
Lab (4.1% CE with Ti) Lab (4.3% CE) Lab (3.9% CE)
Industrial Brake Disks Industrial Test Articles (Ferritized) Industrial Test Articles with Elevated Cr and P
Table 2. Chemistry (wt. %) of Test Articles C
Si 3.26 2.03
Yes Yes Yes Yes
Yes
Aging Effect Confirmation No
Phases, % Area
Ferrite 5-15
25-27 5-7
˜1
40-60 < 0.2
Steadite/Carbides – – – –
1.8–2.0 1.8–2.0
Aging Effect on Machinability
No Effect Improved Improved Improved Improved
Increased Tool Forces, Lower Machinability
Mn 0.61
irons depending upon metal matrix relates to the energy of chip formation. Although gray cast iron is a brittle material in tension, chips can experi- ence significant plastic deformation because the stress state during machin- ing is dominated by compression and shear. If chip formation is assumed to be a plastic strain to fracture event, then changes in fracture toughness would logically affect machining behavior. Fracture work during tensile testing was estimated from the stress-
S 0.08 Cr 0.15 Cu 0.2
displacement curve. In the pearlitic iron, the work of fracture and cutting forces increased after aging. On the contrary, iron ferritized by
heat treatment showed decreased work of fracture and cutting forces due to aging.
Tool Wear and Industrial Machining Measurements
Tool wear is lower when machin-
ing gray cast iron aged at room tem- perature because aged iron requires less work input from the machining
Al 0.01 Ti 0.001 N 0.010
center to form and break off chips. The decrease in required work has been demonstrated by tool force measurements and by testing amper- age drawn while machining unaged and aged iron. The least power was required to machine castings aged for 3-6 days versus iron aged for 1, 9 and 20 days. At that optimal aging time, machined castings had better surface quality (less roughness), but all aged iron had better surface fin- ish than unaged iron. Other tests were performed with
industrial face machining of brake discs for a passenger car. Excessive tool wear produced changing tool geometry and increased cutting forces, which promoted elastic deformation of cast- ing with increasing tilt and destroying required tolerance on perpendicularity (“tilt”). Tilt data from the machining of industrial castings were compared in two ways. Te machining of the 50 unaged castings required two tool position changes. Tool position changes were not required during machining of aged castings after 50 or 200 castings, indicating more consistent dimensions and reduced downtime for tool position corrections. Figure 5 gives a compari- son of measured tool wear for different operations. Aging decreased tool wear significantly in most of the operations.
Industrial Recommendation for Improving Cast Iron Machinability by Aging
Tree possible scenarios exist for
changes in machinability of gray iron during natural aging (Table 1). First scenario: Aging does not occur and therefore, has no influence on machinability. Lack of aging effects in the iron can be caused by elevated
38 | MODERN CASTING January 2014
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76