Feature Seals & bearings
Cage selection: the secret to good bearing performance
In applications involving rolling element bearings, proper attention to cage design and materials selection is essential in order to ensure reliable, long term bearing performance, says Gary Hughes, product engineering manager at The Barden Corporation
he basic purpose of a cage is to maintain uniform ball spacing, but the cage may also be to reduce torque, and minimise build-up of heat and resist harsh environments. In separable bearings, the cage is designed to retain the balls in the outer ring so the rings can be handled sepa- rately. Cage loading is normally light, but acceleration and centrifugal forces may develop and impose cage loading. Also, it may be important for the cage to accommodate varying ball speeds that occur in certain applications. Cages are piloted by the balls or one of the rings. Typically, low to moderate speed cages are ball-piloted. Most high-speed cages have machined sur- faces and are piloted by the shoulder of either the inner or outer ring. High precision deep groove and angular contact ball bearings are avail- able with several types of cages to suit a variety of applications. Cost is a factor with bearing cages, but many others enter into cage design and cage selection, including: low coefficient of friction with ball and race materials; compatible expansion rate with ball/ring materials; low tendency to gall or wear; the ability to absorb lubri- cant; dimensional and thermal stabil- ity; suitable density; adequate tensile strength; creep resistance; high tem- perature; and corrosive atmospheres.
T
and the largest bearings tend to be sup- plied with riveted ribbon cages. One of the benefits of these low speed cages is that they are resistant to operating temperatures above 300˚C.
Both the Crown and Ribbon types are used at moderate speeds and are ideally suited to bearings that are grease or oil lubricated and equipped with seals or shields. The W-type is a low-torque pressed metal cage devel- oped by Barden, and is available in many instrument sizes. It is loosely clinched to prevent cage windup (a torque increasing drawback of some cage designs) in sensitive low-torque applications.
Deep Groove Bearing Cages Deep groove bearings are typically assembled by offsetting the rings, inserting the balls, centralising the rings, then spreading the balls and inserting the cage. Due to this assem- bly method, it must be possible to either insert the cage from one side (snap type cage) or insert half the cage from either side and then secure the two halves together (clinched or riv- eted cage).
For low to moderate speed applica- tions, Barden offers a range of pressed steel cages. The crown cage is the basic cage for the smallest miniature bear- ings. Larger miniature bearings are supplied with clinched ribbon cages,
Factory Equipment MARCH 2012
For higher speeds, Barden offers both the one-piece phenolic snap-in TA-type, and the two-piece riveted phenolic, aluminum-reinforced T cage. The aluminum reinforcement provides additional strength, allowing this high-speed cage to be used in most standard width sealed or shielded bearings, whereas the TA cage offers low vibration in applications where this extra strength is not required.
Angular Contact Bearing Cages Phenolic is also the cage material used by Barden in many of its miniature and instrument angular contact bearings. The cages are machined halo (B and H) types with high-speed capability. A feature of these cages is their outer ring land guiding, which allows lubricant access to the most desired point – the inner ring/ball contact area.
H-type phenolic cages are one-piece units with a through pocket halo design. They are suitable for high-
Selecting the right cage for bearings is essential to ensure good and reliable performance from bearings
speed general-purpose applications. The B-type cage is also intended for high-speed, general- purpose applica- tions, but in separable bearings. The design of this cage includes ball pock- ets, which hold the balls in the outer ring when the inner ring is removed. For high temperature applications, the cages of Barden’s larger spindle and turbine angular contact bearings are machined from bronze or steel – the latter silver-plated. Most of these designs are also outer ring land guided for optimum bearing lubricant access and maximum speed capability.
Non Standard Cages For Specialised Applications Where a standard cage does not meet end user requirements, Barden can develop specialised cages for unusual applications.
Many aerospace bearings, which must be lightweight and able to oper- ate at high speeds, utilise either one- piece snap phenolic cages or two-piece aluminium-reinforced riv- eted phenolic cages. Bronze cages are also used in aerospace systems, partic- ularly in high speed, high temperature conditions such as the generator bear- ings used in aerospace APUs. In some high speed, high temperature applica- tions, silver-plated steel cage designs are the preferred option. In the case of lubricant failure, this silver-plating acts like a solid, dry lubricant. In space applications, where bear- ings must operate in a vacuum at rela- tively slow speeds and loads, cages are often made from PTFE, molybdenum sulphide and glass-fibre reinforced material acting as a dry lubricant.
Turbomolecular and Dry Pumps For grease-lubricated turbomolecular bearings, phenolic cages are typically used, as they can operate at high speeds and offer extended lubricant life. For oil-lubricated turbomolecular bearings, machined plastic (Polyamide-imide) cages are the preferred option. These provide good resistance to high temper- atures and help to feed oil into the bear- ings. Here, the cage is designed as part of the oil circulation system, redirect- ing the oil to difficult to reach areas of the bearing.
In dry pump applications, although the bearings operate at slower speeds, they have to resist higher contamina- tion levels and poor quality lubricants over the complete life of the bearings. Therefore, steel riveted cages are the preferred choice. However, current developments in high strength plastic (PEEK) cages are pushing this technol- ogy into higher speed applications. The Barden Corporation T: 01752 725531
www.bardenbearings.co.uk Enter 326
29
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56