FEATURE INSPECTION & MEASUREMENT
X-RAY TECHNOLOGY helps to play it safe
German dairy company, Karwendel-Werke Huber, is monitoring the quality of its cream cheese and quark specialities with the help of 11 X-ray inspection systems from Ishida Europe
T
wo models from the Ishida X-ray range have been installed at
Karwendel-Werke Huber, the IX-GA- 4075, which is inspecting plastic tubs with fill weights between 135 and 500g, and the IX-GA-65100, which is able to inspect crates packed with six and 12 individual packs “en bloc”. As well as its soft cheese and quark specialities, the X-ray systems are inspecting plant-based products from Karwendel’s subsidiary NOA, dealing in total with 15 different pack formats. Foreign body detection with metal
detectors was not an option because of the metallised (aluminium) film lid and Karwendel also wanted to be able to detect non-metallic foreign bodies. This includes, for example, small stones in the herbs and spices formats and pieces of fruit cores that may accidentally end up in the soft cheese and quark formats. The requirements profile demanded the
reliable detection of specific foreign body particle sizes (for example, 1mm stainless steel, 2mm glass and 4mm PTFE plastic). “Thanks to their relatively
homogeneous mass, our products can be detected relatively easily by X-ray inspection systems,” reports Stefan Schindler, head of quality management at Karwendel-Werke Huber. “However, high performance levels are required, as all of our production lines work at speeds
of 172 cycles per lane (often using twin lanes) and per minute. “The decisive factor for us was the ease
of operation and the display’s practical user interface,” adds Schindler. To save space upon integration on the
production lines, the Ishida X-ray inspection systems feature cooling units fitted on top of the machines. The ultra- strong protective metal curtains at the inlet and outlet of the inspection chambers have been customised for each application. To reduce noise levels, the infeed and outfeed conveyors on some of the X-ray machines are fitted inside noise absorbing tunnels.
ENHANCE INSPECTION SENSITIVITY The Ishida X-rays are operating in a three-shift system. On nearly all production lines, packs are running through the inspection chambers on twin lanes at a maximum belt speed of 40 metres per minute. Despite this challenging throughput, even very small foreign bodies are reliably detected. The inspection system technology
works regardless of the temperature, salt and water content of the product. It is also possible to test only defined product areas and to ignore specific parts of the packaging, such as the seal areas. The machines use patented software with a self-learning algorithm called Genetic Algorithm (GA). By analysing image data over a number of generations, it is possible to enhance inspection sensitivity by approximately 20 per cent. At Karwendel-Werke Huber, any packs
that have been identified as faulty by the system are isolated in a central collection bin using an air reject; these are sealed and can only be opened by authorised personnel. IX-GA-65100 X-ray inspection systems with extra-large inspection
16 NOVEMBER 2017 | FACTORY EQUIPMENT
Above: Two X-ray systems inspecting Exquisa soft cheese at Karwendel-Werke Huber
Below: Easy operation was one of the key drivers to invest in Ishida X-ray Inspection Technology
chambers use an arm reject to separate out-of-spec crates and guide them to a lockable collection table. Data logging records all optical and numerical information to allow seamless traceability. The Ishida IX-GA X-ray inspection
system is controlled by touchscreen on a Windows interface. A special monitor cover permits access to authorised employees only by means of an RFID chip. After an automatic set-up process, the machines are ready for use within 90 seconds, after which time further fine adjustments can be made. Product changeovers are implemented via the fast retrieval of up to 100 programmable pre- sets. Cleaning is also easy, thanks to the accessible stainless steel construction, and the conveyor belts are easy to remove and replace without the need for tools.
THE NEXT JOINT PROJECT The machines at Karwendel-Werke Huber also collect a lot of valuable data at the end of the lines, and the dairy company wants to take advantage of this data soon. Therefore, the next joint project with Ishida will be the implementation of the IDCS (Ishida Data Capture System) software. This web- based program connects the X-ray inspection systems and records efficiency information such as downtime, performance and quality. The relevant data for each product and pack format can then be analysed in real time and displayed graphically, sorted by product batch, shift, operator, product, machine or line. The displays and reports are user-defined and can be individually adapted; the parameters can be accessed online at any time during operation, without interrupting production. The IDCS II software is suitable for
measuring Overall Equipment Efficiency (OEE) and offers an important business control function. Karwendel says it expects a direct increase in productivity as a result.
Ishida Europe
www.ishidaeurope.com T: 0121 607 7700
/ FACTORYEQUIPMENT
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49
