Preliminary Agenda Abstracts WEDNESDAY, AUGUST 24, 2022, con’t.
9:35 a.m. – 10:05 a.m. Development of of Ni Based Superalloy with High Temperature Strength, Low Density & Excellent Castability for Turbine Wheel Yoshiki Kumagai, Daido Steel Co., Ltd. As automotive exhaust emission is strictly regulated all
over the world, higher fuel efficiency and cleaner exhaust gas in combustion engines have been required. Recently, downsized engines combined with turbocharger have been one of effective solutions to improve fuel efficiency. To improve combustion efficiency, an exhaust gas temperature is increasing, therefore higher temperature resistance is especially required for turbine wheel in turbocharger. IN100 is one of the candidate alloy as it has high temperature properties with low density. However, it has low castability due to poor ductility at high temperature. In this study, the balance of Al and Ti composition was optimized from IN100 to improve the high temperature ductility by expanding the γ single phase region below the solidification temperature, while obtaining the high temperature strength by maintaining the volume fraction of γ’-Ni3(Ti,Al) phase equivalent to IN100 around 1000 °C. Furthermore, the high temperature creep rupture life increased by adding a small amount of Ta. The developed alloy was successful to produce the turbine wheel without surface crack and misrun. Thus, the developed alloy in this study has high castability, low density and high specific strength at high temperature. This alloy is being commercialized as a new turbine wheel material by Daido Castings Co., Ltd., and the evaluation has been proceeding by customers for the near- future applications.
10:05 a.m. – 10:20 a.m. BREAK
10:20 a.m. – 10:50 a.m. Wireless Sensors for Investment Casting Shell Data Acquisition Nathaniel Bryant, University of Northern Iowa Current investment casting methods include a degree of
process variation that has been the source of casting defects and ultimately delays in product delivery. It is estimated that quality issues including casting defects resulting from process variation can cost manufacturers millions in rejected parts or delivery delays. Determining variations in the shelling and casting process can predict casting success and provide valuable information to improve the casting process. This information can form the basis for foundries wishing to advance into manufacturing 4.0. Data from the shelling and casting process can aide metal casters in refining their processes to higher levels than ever before possible. Sensors within molds can collect process data which include temperature, pressure, moisture, gas chemistries, shift and rotation detection, and
24 ❘ June 2022 ®
the magnetic field. The magnetic field, for instance, may provide insights into the flow of metal in mold cavities or even solidification. The University of Northern Iowa and Youngstown State University have developed a new low cost technology that has the ability to track the investment casting dipping and drying process along with casting data and transmit the results wirelessly for documentation. The technology uses low cost microcomputers and has the ability to sense and measure several critical characteristics simultaneously. The low cost of the technology utilized allows multiple trees to be tracked, individually recording their information.
10:50 a.m. – 11:20 a.m. Advanced Plasma Coating of Wax Injection Moulds – Eliminating Release Agents from the IC Process Dr. Dirk Lehmhus, Fraunhofer IFAM Investment casting is based on processing large quantities
of lost wax patterns. The common process for producing these is wax injection moulding, which requires release agents (e.g. silicone oils) to facilitate the demoulding process. Without these release agents, ejection of the wax patterns without damage is impossible. However, the use of release agents entails a number of disadvantages, among them economic and environmental as well as health issues. These include the cost of cleaning wax patterns to wash away residues of release agents, as well as the contamination of the working environment and thus possible health hazards for employees caused by silicone aerosols. Furthermore, release agents can bring about quality issues in the wax room and necessitate costly efforts at their removal from the injection moulds. In our successfully completed research project funded by the German Federal Ministry for Economic Affairs and Energy (BMWi, AiF IGF 18915N), an innovative, ready-to-use alternative has been developed in the form of a long-term stable plasma polymer release coating which allows complete elimination of any additional release agent. This surface coating is characterized by its excellent adhesion to the metallic mould and in particular by its high cohesion strength and low surface energy. The coating exactly reproduces the geometry and surface features of the injection mould and does not influence its dimensional accuracy, as the maximum layer thickness is limited to approx. 2 µm. The coating can be applied both on new and already used production moulds. Re-coating has also been demonstrated successfully. In the
EVENT SPONSOR
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44
