Feature Electrical Design Software
Be sure to check under the bonnet W
When selecting or working with electrical design software it is vital to understand exactly what the software is capable of and what features are available. Philip Grace, senior support engineer at Amtech, explains
hen using a piece of software it is not unusual to think, ‘I wish it did that, because it would make my life much easier’. In addition, how many of us have been carrying out everyday tasks in a fairly laborious manner for ages, only to find that your software offered smarter ways of doing it but you just hadn’t realised they were there? These are certainly experiences that many of us have had, and they emphasise the importance of under- standing what particular software programs can and can’t do - ideally before you buy it. Purchasing soft- ware that only does half the job can be very frustrating.
Even if you’ve already invested in software, it’s worth checking whether it can already do something you think would be helpful. Often a quick call to the technical support people will make you aware of features you didn’t know existed, with the potential to save a lot of time.
For example, if you’re designing a project you will probably design the whole scheme in your design software. So the schematic will include all of the key information such as cable sizes, busbars, loads, protective devices etc. However, there is a strong likelihood that something will change
Below: following the electrical design of projects, there is a strong likelihood that something will need changing - a sometimes time consuming and laborious process. Amtech’s data entry spread
control feature can help to speed things up
with the project that will necessitate a change after you’ve completed the elec- trical design. In many cases this may entail re-visiting the schematic to change a particular setting several times over.
Speeding things up
In such cases, it can be very time con- suming to go back to each element to change them one at a time. Some soft- ware developers have recognised this and included a tool to speed things up, but you have to know the feature exists. In Amtech’s software, for example, it is called data entry spread control. The way this works is that the data embedded in the schematic can be viewed in spreadsheet format so that many of the data management tools found in spreadsheets can be applied to the design. Ideally, the information should be broken down into component types, each with its own tab. The settings available are generally the same as those in the cable, load details and motor details dialogs and are contained in the same tab pages. In this way, all of the key informa- tion is visible and can be managed using spreadsheet features such as ‘sort’ and ‘filter’. This means that the components that are going to be sub- jected to the same change (e.g. cables that are to change length) can be selected together. They may be in adja- cent rows, so they can be selected with a ‘click and drag’, or by clicking the
first row and shift clicking the last row to select all the rows in between. If they are not adjacent, multiple items can be selected by holding down the control key and clicking on each of the rows to be selected.
Once all of the selections have been made, the required change can then be applied to all of them in a single action, thus eliminating the tortuous process of working through them individually. This process can be repeated for every type of component that needs to be changed. Then, when those changes are saved they are represented in the schematic. Of course, it’s useful if the soft- ware flags up a warning when you are about to change multiple components, but even if you do something wrong, the ‘undo’ feature in the spreadsheet will allow the original data to be restored one step at a time, up to ten previous steps. This process can be used for all sorts of information. For instance, it may be necessary to change the cable type for armoured cable due to unanticipated factors on-site. Again, the process described can be applied so that many changes are achieved in one action. This is just one example of the sort of features found in some design software that can save time. So if you’re thinking of buying software it’s worth taking the time to check that it’s going to do every- thing you want. If you are already using design software it’s a good idea to check just what it’s capable of - perhaps under- taking some extra training to maximise the return on your investment.
Amtech
www.amtech.co.uk T: 0800 028 2828
Enter 222
Electrical Engineering APRIL 2012
29
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44