DS-SEP24-PG54+55_Layout 1 18/09/2024 14:39 Page 1
FEATURE
FASTENINGS & ADHESIVES
ARE STRUCTURAL ADHESIV TO MECHANICAL JOINING?
In thousands of applications, structural adhesives are being used as an alternative to mechanical connections such as screws, rivets, or spot welds. Peter Swanson, managing director of Intertronics, weighs up mechanical bonding vs adhesive bonding, and gives some advice for designing in an adhesive
S
ometimes known as ‘chemical joining’ – to contrast with mechanical joining – adhesive bonding involves an adhesive ‘hardening’ to
provide a joint capable of bearing the forces that it is subjected to over the product’s lifetime, while enduring the associated environmental conditions. An adhesive can be considered to be cured when a chemical reaction has taken place and its constituent parts (monomers or oligomers) join up and cross-link to become larger molecules (polymers).
ADHESIVE BONDING ADVANTAGES Adhesives bring many advantages over mechanical joining methods, including improved stress distribution. Once cured, an adhesive bond is continuous and offers a more uniform stress distribution – the joint’s entire surface carries the load, rather than an individual point, avoiding the local concentration of stress found in mechanically joined parts. Adhesives can also minimise or eliminate
corrosion, boost impact resistance, avoid joint fatigue, provide electrical insulation, and dampen vibration. In many applications, an adhesive can also act as a sealant, protecting the assembly from water, moisture, dirt, and other
environmental contaminants. For example, when working with a manufacturer of safety torches who were looking to make their products more rugged, Dymax Multi-Cure 621-T was recommended, which worked as both an adhesive and sealant when bonding the lens to the reflector housing. Another customer, Process Instruments, found success with IRS2125 flexible epoxy adhesive, bonding two stainless steel surfaces, while waterproofing its IP-rated seal. Adhesives are often selected by manufacturers, such as those in automotive or aerospace applications, to reduce the weight of assemblies. Mechanical fastenings are often made of metal, and their weight can add up in applications requiring multiple fastenings. While adhesives are not inherently lightweight, their ability to distribute stress can give design engineers freedom to reduce part thickness and therefore weight, while removing the weight of metal fastenings. Furthermore, adhesives can bond in
applications where mechanical fastening would be difficult due to design complexity – such as composite sandwich structures – or when bonding different substrates, such as metal to
plastic or glass. They can also bond both similar and dissimilar substrates (differing in composition, moduli, coefficients of expansion, or thickness), mitigating different expansion rates. For metals that will be subjected to thermal cycling or may be at risk of galvanic corrosion, adhesives can provide a more reliable solution. In addition, an adhesive can provide an almost invisible bond, improving aesthetics. Beyond these technical benefits, adhesive bonding can bring operational benefits in reduced component costs, lower labour and assembly costs, and reduced finishing costs. If a fast curing adhesive is specified, this can improve production speed greatly, while simplifying operations.
DISADVANTAGES All adhesives do, however, carry some disadvantages. Structural adhesives generally have bond strengths in the order of 2,500 to 7,500 psi, and tolerate temperature swings up to 170˚C. Adhesives are polymers, and therefore not as strong as metals, although this is offset by the increased surface contact area of a bonded joint. A downside is that adhesives may be affected by increased temperature, which can reduce the bond strength and chemical resistance. Where traditional mechanical joints offer
instant strength, adhesives reach full strength once the curing reaction is complete. This can happen in seconds, to hours, to days, and the assembled joint must be fixtured for at least part of the time the part is curing. Prior to cure, the adhesive must wet the substrate in order to create a successful bond – surface treatment may be required if bonding a substrate with low surface energy, which adds an additional process.
DESIGNING WITH ADHESIVE IN MIND There are an increasing number of structural adhesives on the market and, as there is no universal adhesive, manufacturers will have to select which candidates are the best to evaluate for their applications. This involves considering the design, production, and processing considerations, and developing a specification based on the necessary properties and allowable compromises. There are multiple structural adhesive
chemistries, the most common being polyurethanes (PUs), epoxies, and methyl methacrylates (MMAs), but some cyanoacrylate
54 DESIGN SOLUTIONS SEPTEMBER 2024
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64
