Pharmaceutical & medical
Enabling smallEr and safEr mEdical dEvicEs
Healthcare organisations are increasingly moving patients to home care settings to reduce the pressure on traditional healthcare facilities, especially since the COVID-19 pandemic. However, this has been a double-edged sword for medical device manufacturers. On one hand, it has meant a boom in the market for certain home medical devices, but it has also led to greater scrutiny of devices and increasingly stringent safety standards. Here, Andy Selvy, chief system designer at industrial heater manufacturer Watlow, explains how and why medical device manufacturing needs a new approach.
their equipment in an uncontrolled environment by untrained users. Meeting safety standards is sometimes
T
possible with traditional technology, but that technology adds to both the bulk and the cost of medical devices. Device manufacturers understandably want to make devices that are smaller, cheaper and easier to use - goals that are often at odds with safety compliance measures. This is where innovation in thermal solutions, including heaters, sensors, temperature controllers, power controllers and their supporting software can make a difference.
THERMAL SYSTEM SAFETY Many medical devices require heaters to warm gas or liquids, and these require a fair amount of power that increases the possibility of leakage current and hence the risk of electrocution.
he IEC 60601-1-11 standard for medical electrical equipment requires manufacturers of home medical devices to identify product safety risks associated with using
This is a great example of where stricter standards for home care medical devices exist and how evolving heating technology can better meet those standards. Unlike medical devices in a clinical setting,
home medical devices cannot be designed with the assumption that there is a trained operator on site that can use tested outlets and equipment according to a set procedure. As a result, safety precautions must be built into the device design itself. One way to improve patient safety is to
incorporate an isolation transformer to step down the voltage going into the device, similar to the “brick” used to step down voltage for a smartphone charger. But isolation transformers are notorious for being big, bulky and expensive, which works against the goal of miniaturisation for home medical devices.
SAFETY VERSUS MINIATURISATION So, what is the solution to ensuring safety without the need for bulky and expensive technology? It starts by designing devices within a systems approach. For instance, it is not sufficient to create a
heater that runs at 95 microamps leakage so that it can be incorporated into a device that must be rated to run under 100. Although this type of heater would meet the given specification, it would take up most of the available leakage budget. Adequate heater design of the entire thermal system must take into consideration these difficult system level requirements.
56
January 2023 Instrumentation Monthly
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82
