AEROSPACE
playback the complete sequence, with the operator taking on only a supervisory role.
MRO An equally important application for electron beam welding in the aero- engine industry is repair and salvage. The general wear and tear on components within the arduous environment of the combustion gases, the strain on materials operating at high loads, often at high temperatures, create a continuous need for replacements. High costs and long lead times are
this type of product. The part requires linear, circumferential, and planetary welds during successive operations. As a major rotating component, the
compressor rotors demand welds of high integrity, in 901 nickel. Fabrication by electron beam welding achieves savings in weight, material, and machining costs. The aero-engine industry has taken maximum advantage of the attributes of electron beam welding, the design of many components is based on its application. The industry requires fabrications
from various materials that are often difficult to weld by other methods such as forgings, pressings, or castings, often in a fully machined state. Although the finished fabrications may be complex, they will invariably be from relatively simple constituent parts. You can achieve lightweight yet rigid assemblies economically from the most appropriate materials. Fabricated using electron beam welding
to join the many blade sections together results in a precise, repeatable weld. Titanium, for example, is perfectly suited to the electron beam welding process as it is done in a vacuum to avoid oxidation. Electron beam welding can be reliably
and repeatedly applied using established parameters and techniques that can be readily set up on a machine, even for small batches or one-off production.
Stator blades An early application within the aero- engine industry was the welding of stator blades. The individual blades are cast in a range of steel or nickel-based alloys and are typically heat- and/or corrosion-resistant. The blade platforms
also have varying sections, and there is a need to maintain close dimensional tolerances. Therefore, the range of joining methods that meet all criteria are strictly limited. The high-voltage beam of electrons is particularly successful in this type of application, where the thickness of the section may vary, yet throughout the progressive fusion, you can use the same weld parameters. Fixtures are designed to accommodate
several assemblies depending on component size. During the evacuation of the work chamber, the first joint is brought into view. As soon as the system reaches the correct pressure level, that joint is welded, and the X-Y table is indexed to the next joint. With several welds produced at each evacuation cycle, the total floor-to-floor time per weld may be less than 1 minute. Alternatively, a different approach would be to weld the complete ring in one evacuation cycle. The welding procedure for each joint
between blade platforms requires four weld passes: tack and finish weld for the outer platform, tack weld, and finish weld for the inner platform. Each weld pass requires a different set of beam settings and a different pattern of movement of the workpiece manipulator. Because of the complexity of the total weld program, machines for this application incorporate teach-and-replay CNC, whereby the operator first teaches the system each of the subroutines for the four weld passes. Next the system has to be taught the angular position of each joint in a sequence that distributes the heat to minimise any possible distortion. From this point, the operator has only to initiate the welding cycle and for the machine to
inevitable, but repair schemes can ensure a speedy, relatively low-cost turnaround of damaged or worn items. Because of the potential savings, most of the world’s airlines have installed their engine overhaul facilities and many of these incorporate electron beam welding. Repair schemes based on electron beam welding have approval for many components for both civil and military engines. The welds are produced in a variety of
materials and frequently in areas where access is limited. There is the added problem that, while in new parts, it is possible to ensure sufficient material to provide for any minor distortion; in repair work, you must base the scheme on the finished dimensions of the component you are repairing. An interesting aspect of electron beam
welding is its ability to weld together certain dissimilar metal combinations. This feature has been used within the industry to its advantage in several repair and salvage schemes where the added-on part has been produced in a material able to achieve a longer operational life than the original.
www.camvaceng.com
www.awd.org.uk
WeldingWorld1 / 23
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43
