search.noResults

search.searching

saml.title
dataCollection.invalidEmail
note.createNoteMessage

search.noResults

search.searching

orderForm.title

orderForm.productCode
orderForm.description
orderForm.quantity
orderForm.itemPrice
orderForm.price
orderForm.totalPrice
orderForm.deliveryDetails.billingAddress
orderForm.deliveryDetails.deliveryAddress
orderForm.noItems
Page 58


www.us-tech.com


October 2026


Engineering Parylene Protection for PCB Assemblies


By Michael Hunter, Value Add and Failure Analysis Engineer, ICTC


value depends on the failure mechanism be- ing controlled. Selecting a premium material does not compensate for contamination, in- complete coverage, or poorly defined masking requirements. For high-reliability electronics, coating


P


selection should begin during design review. Engineers need to identify the expected envi- ronment, vulnerable surfaces, and evidence required to demonstrate protection. Those decisions affect component se- lection, cleaning, inspection, rework, and supplier qualification. Parylene is deposited from the


vapor phase, forming a thin polymer film over exposed surfaces, edges, and complex geometries. A solid dimer is vaporized, cleaved into monomer, and introduced into a vacuum chamber, where it polymerizes on surfaces at or near room temperature. The process avoids liquid solvent flow and pooling while adding little mass. This deposition method can be useful on dense assemblies, fine fea-


arylene conformal coating can protect electronic assemblies against moisture, corrosion, and electrical leakage, but its


tures, and sharp edges. It also makes mask- ing critical: any surface exposed to the process may receive coating, including con- tacts and other areas that must remain bare.


Selecting the Coating Material selection should reflect both re-


liability requirements and manufacturing constraints. Acrylic coatings offer relatively low cost and easier removal, making them useful where environmental exposure is moderate and rework is likely. Urethanes


provide chemical and abrasion resistance but are generally harder to remove. Silicones provide flexibility for applications involving thermal expansion or vibration, although contamination control and repair compatibil- ity require attention. Parylene becomes attractive when thin,


conformal coverage and dielectric or barrier performance justify specialized equipment, masking labor, and more demanding rework. Comparing application prices alone can over- look the costs of inspection, qualification, yield loss, and field failure. Parylene C is commonly selected for moisture and corrosive-gas protec-


A nominal chamber thickness does not prove adequate protection at every functional surface.


Parylene selection links environmental exposure and


failure mechanisms to coating choice, design controls, process controls, and verification.


tion. Parylene N may be appropriate when low-loss dielectric behavior and penetration into fine features are pri- orities. The choice should be supported by the required thickness, critical geometry, and application evidence.


Continued on next page


See at SMTAI, Booth 2624


Page 1  |  Page 2  |  Page 3  |  Page 4  |  Page 5  |  Page 6  |  Page 7  |  Page 8  |  Page 9  |  Page 10  |  Page 11  |  Page 12  |  Page 13  |  Page 14  |  Page 15  |  Page 16  |  Page 17  |  Page 18  |  Page 19  |  Page 20  |  Page 21  |  Page 22  |  Page 23  |  Page 24  |  Page 25  |  Page 26  |  Page 27  |  Page 28  |  Page 29  |  Page 30  |  Page 31  |  Page 32  |  Page 33  |  Page 34  |  Page 35  |  Page 36  |  Page 37  |  Page 38  |  Page 39  |  Page 40  |  Page 41  |  Page 42  |  Page 43  |  Page 44  |  Page 45  |  Page 46  |  Page 47  |  Page 48  |  Page 49  |  Page 50  |  Page 51  |  Page 52  |  Page 53  |  Page 54  |  Page 55  |  Page 56  |  Page 57  |  Page 58  |  Page 59  |  Page 60  |  Page 61  |  Page 62  |  Page 63  |  Page 64  |  Page 65  |  Page 66  |  Page 67  |  Page 68  |  Page 69  |  Page 70  |  Page 71  |  Page 72  |  Page 73  |  Page 74  |  Page 75  |  Page 76  |  Page 77  |  Page 78  |  Page 79  |  Page 80  |  Page 81  |  Page 82  |  Page 83  |  Page 84  |  Page 85  |  Page 86  |  Page 87  |  Page 88  |  Page 89  |  Page 90  |  Page 91  |  Page 92