News Sponsored by
ARE YOUR LOADING BAY SAFETY SYSTEM MAINTENANCE COSTS
CUTTING INTO PROFIT? The loading bay is an essential part of any manufacturing company, warehouse, or distribution center. It is what allows the process of raw materials to enter and completed goods to be transported to consumers and end users. Unfortunately, the loading bay can be a hazardous environment where accidents can occur. It is estimated that 25% of all industrial accidents happen at the loading bay according to ISHN.
To mitigate the risk of accidents, organisations often invest in loading bay safety systems to mitigate the risk of accidents or injury at the loading bay. A variety of systems can be found on the market to prevent these incidents such as hook restraints, wheel chocks, blocking arms, and interlocking gladhand systems.
Organisations often invest in these systems to avoid accidental injuries at the bay and spend anywhere from thousands to millions for a corporate or site wide roll out of one of these systems. Companies expect these systems to be a one-time investment that will prevent them from incurring the costs associated with a workplace injury or potential death.
What companies don’t expect is the high recurring maintenance costs associated with some types of loading bay safety systems. Loading bay safety systems typically fall into the categories below and can vary in maintenance costs:
Automatic Wheel Restraints: Automatic wheel restraints such as powered chocks perform in a similar
way to mechanical chocks; however, they are automatic and thus require no personnel in the yard to fit it. They are also integrated with other bay equipment which ensures that a safe process is enforced. Some systems are built in at sub ground level and therefore require significant installation effort, these can also be significantly affected by the elements. Systems that are installed above ground become an obstacle, especially in winter.
Like mechanical chocks, relatively high maintenance costs can be associated with these systems due to the number of moving parts, concrete work associated with damaged equipment, and the time associated with clearing snow/ice in harsh weather conditions.
Hook Restraints: Hook restraints can be manual or automatic systems that prevent drive aways at the loading bay. The hook restraint is installed at the bay door and when a truck is present, the hook is engaged and clamps onto the ICC bar of the vehicle to prevent the trailer to pull away from the bay prematurely.
Mechanical Chocks/Wheel Restraint: Mechanical chocks build upon the principle of manual chocks however they typically have additional permanent structure that they are fitted to which provides increased restraining force. If the permanent structure is higher than ground level, these can become an obstacle, especially in winter when ploughing the site. Ground level plates can also be affected by winter conditions as they become covered in snow/ice, making it difficult to fit the chock.
There can be high maintenance costs associated with this these types of restraint systems due to the
number of moving parts, damage to permanent structures, and the time associated with clearing snow/ice in harsh weather conditions.
Manual Chocks: Manual chocks are common, simple wedges of material that are placed closely against a vehicles wheel to prevent accidental drive aways.
Chocks can be unreliable as they can easily be lost, stolen or break. Maintenance cost for manual chocks include complete product replacements and can vary due to the number of sets of chocks the facility owns.
Interlocking Gladhands: Gladhand devices are used to lock out the air brake of the trailer to prevent movement at the loading bay. When gladhand devices are interlocked with the bay door with fixed mounted trapped key interlock devices, they can create a sequential safety process that must be followed to load and unload the trailer that results in the prevention of drive aways at the loading bay.
Maintenance costs associated with these systems are minimal as the only maintenance required is the greasing of the gladhand coupling device once per year depending on the temperature of your facility’s location.
In the chart to the left, common loading bay safety systems are ranked from the highest to lowest associated maintenance costs for a facility with 25 loading bays over the time period of one year.
Safety at the loading shouldn’t cause additional headaches, it should be simple, safe, and low maintenance. Lucky for you, there are other options than your existing solution that won’t cut into your facilities profit.
Email:
sales@castell.com
www.castell.com
22 | TOMORROW’S FM
twitter.com/TomorrowsFM
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70
