MATERIALS HANDLING
transfer of waste return slurry from concrete slab manufacturing processes. Xella, a European specialist in building and insulation materials, finds that the pumps are ideally suited to conveying the abrasive slurry on a repeatable and reliable basis, overcoming issues with previously deployed progressive cavity (PC) and centrifugal pumps. With its Ytong, Silka and Hebel
brands, Xella is one of the world’s largest manufacturers of autoclaved aerated concrete (AAC), a well-known and proven ecological building material. AAC offers high thermal insulation and, thanks to its porous structure, can undertake both structural and physical building functions, normally without additional measures or supplementary building materials. Xella, a 6,000-employee company, has 91 plants in 20 countries. Importantly, the company’s products are sustainable both in manufacture and use. To Xella, sustainability means more than simply bringing energy- efficient and environmentally compatible products to market; it is also about production, management, human resources, compliance and research.
ABRASIVE SLURRY As part of the company’s manufacturing process, the reuse of otherwise waste slurry streams is a priority. Te raw materials for AAC include quartz sand, calcined gypsum and lime (mineral), which are mixed with water to an aqueous suspension. Te aerating agent is aluminium powder, which is added at the end of the process to a concentration of 0.05-0.08% by volume, depending on the pre-specified density. Finally, the mix is poured into moulds. When the forms are removed from the material, it is solid but still soft. Te material is then cut into blocks or panels, and placed in an autoclave chamber for 12 hours.
Te waste after cutting falls into a sump. Tis is diluted with water and flows to an underground tank, from where it is circulated
36
www.engineerlive.com
PUMPS S
PREFERRED
Hose pumps preferred in abrasive cement slurry applications
everal Bredel pumps from Watson- Marlow Fluid Technology Group (WMFTG) are proving highly successful in the circulation and
and transferred by Bredel pumps. Te slurry has a specific gravity (SG) of between 1.45 and 1.7 at ambient temperature, along with a viscosity of approximately 100-150 cPs and a solids content 723 g/l.
THE DUTCH PLANT Two Bredel 80 pumps and one Bredel 100 are installed at the company’s production facility in Meppel, the Netherlands, where they have been used in this application for several years. Te site operates a four- shift system running 144 continuous hours per week (there is no production on Sundays). Bredel hose pumps are favoured by Xella
for various reasons. For instance, this type of pump has no valves or seals to leak, clog or replace. It provides flow rates to 108,000 l/h and pressures to 16 bar. Te pumps can also handle viscous and abrasive slurries, pastes and sludge, with up to 80% solids in suspension. In the past, the Dutch plant used progressive cavity (PC) pumps, but these were replaced with Bredel due to high maintenance costs and long downtime periods. At Meppel, one of the Bredel 80 pumps
runs 90% of the time, circulating the slurry in the tank underneath the cutting machine at a rate of 14.5m3
/hr. Te slurry in this tank overflows into a back-up tank,
which is where the other Bredel 80 is deployed, pumping the slurry to a bulk storage tank. As for the Bredel 100, this is used to pump slurry from the bulk storage tank to the mixer at flow rates of between 13.8 and 18 m3
/hr, along several long-sweep elbow bends in the system.
THE GERMAN PLANT Xella has also migrated Bredel technology to its plant at Rotenburg in Germany over the past two years. Tis site operates two Bredel 100 pumps for circulation and transfer of the waste return stream. At Rotenburg, the application involves
the circulation and transfer of schlamm or cement slurry, replicating the duty of the Dutch site but exclusively using the higher flow Bredel 100. During slurry transfer, the outlet is into a tank that is mounted on a load cell, while the pump is located near the tank where the cement slurry is mixed by an agitator. Suction is from the bottom of the tank with a three-way valve connecting the pump to the tank, or the flush line. Te pump runs at 26rpm (at 50Hz) and up to 5 bar pressure. Tere exists the potential for two more Bredel 100 pumps on site. Te facility in Germany previously
deployed centrifugal pump technology, but ongoing problems were experienced, largely due to various additives in the cement slurry. By circulating the slurry, the particles become smaller and smaller and, at a certain size, air bubbles are created. Unfortunately, the air bubbles led to the formation of air pockets in the centrifugal pumps, causing them to fail, a situation since rectified by adopting the Bredel pumps.
The cement plant is reaping numerous benefits from Bredel pumps
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68
