PLANT MANAGEMENT
A
n engineering company is recommending a three-step action plan to help the food processing industry reduce bacterial
contamination and costs.
“90% of bacterial contamination in the food processing industry is caused by poor hygienic design, with gearboxes and motors a primary cause of problems,” explains Gareth Lenton, director of the Power Transmission Technology Centre at ERIKS UK. “Our experience has helped us to identify three common problems, which form the basis of our three-step plan.” Specify motors equipped with anti- condensation breathers. “Condensation build-up can harbour bacteria, shorten operational life,and result in unnecessary downtime and increased maintenance costs,” explains Lenton. “An anti- condensation breather compensates for the pressure diff erential between the warm air inside the motor and the cooler air outside, which prevents condensation and water from building up inside the motor. T is leads to less corrosion, less monitoring and longer meantime between failure.” An ingress protection rating of IP66 to IP69 will also protect a motor from water jets and chemical cleaning products. Choose gears and motors that have smooth
surfaces. “Cooling ribs, hollow areas and sharp edges are the perfect hiding places for food because they’re often immune to
ERIKS recommends a dedicated plan to reduce contamination
C COMBAT
daily wash-down procedures,” Lenton says. “Bacteria then multiply in these spots and will eventually enter the food.” Motors with round and easy-clean
designs prevent food from accumulating, thereby reducing the risk of contamination. “For the best results, look for motors without tag plates,” advises Lenton. He adds, “Hollow torque arms and shaft covers, such as those on the Fenner Hypoid and Fenner KH, are also easier to clean.” Make the switch to stainless steel.
“We know of one multi-national grocery retailer that wants its suppliers to exchange existing geared units for stainless-steel designs,” reveals Lenton.
Gareth Lenton, director of the Power Transmission Technology Centre at ERIKS UK
28
www.engineerlive.com
It’s easy to see why. Gear corrosion – specifi cally housing and bearing rust – can build up over time and even enter
ONTAMINATION
An expert presents a three-step action plan for preventing cross-contamination in food processing
the food. Lenton states: “Our experience suggests that the use of stainless-steel geared motors would speed up cleaning times and reduce the use of chemicals, which could potentially save food processors up to 60% on cleaning costs.” Even though this plan only covers
gearboxes and motors, food processors that implement it stand to see signifi cant improvements in the lifespan of critical equipment, overall costs for cleaning and the safety and quality of their products. Lenton comments that, “T ere’s also the reduced risk of non-compliance with the regulations that govern the food industry, such as BRC and IFS certifi cates. T e peace of mind that comes from knowing, rather than hoping, for a positive outcome from an inspection is, in itself, invaluable.”
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68
