cones reels and can damage reel bearings.
The time spent annually lapping mowers vastly exceeds the time it takes to face the bed-knife, with a facer or file and in-situ spin-grind a reel properly.
Is it a scythe?
When you set a mower as a scythe the reel becomes a gathering device, bringing the grass crop to the bed-knife. The bed-knife is the scythe’s cutting- edge. Correctly sharpened and angled, it allows it to present the grass crop for the reel to pull in against the sharp front cutting edge. No contact is required between the reel and bed-knife when setting as a scythe, just sharp edges, particularly on the bed- knife. The spiralled helix shape of the reel blades are designed to provide a sideways action when drawing the grass along the bed-knife. The bed-knife has to be sharp at all times.
Scissors will cut, but a scythe cuts cleaner. This is precisely why a surgeon uses a single-blade scalpel (which is drawn through the flesh) instead of scissors.
When setting the mower as a scythe, with zero reel to bed-knife contact, there is no need for a blade thinning a relief, 100% relief is there all the time, so the machine runs easier and with less energy input, less fuel use, lower hydraulic pressures and so on.
When using an easy to set, in-situ type spin grinding method with the ability to set up and sharpen quickly, you can lightly renew the reel’s edges as needed, face up the bed-knife and always keep the “no contact” setting in minutes. This is a scything cut. To maintain a scything cut the bed- knife is the most important part. The bed-knife has three functions:
1. Presentation - the front face edge primarily stands the grass up and presents it for the reel, at the right height. It must be sharpened at the correct angles.
2. It is a cutting edge, therefore, the bed- knife must always be sharp.
3. Ejection - the top face angle is for ejecting the grass cuttings from the cutting edge. This angle will vary according to the mower’s intended use, but the top face angle is never
112
smaller than the reel diameter. Therefore a 5 inch diameter reel will require a 5 degree top face minimum, then add 2 or more degrees for the grass crop on say a fairway cut. This will vary in different growth conditions.
Bedknives do all of the cutting when you set up a mowing unit like a scythe, the blade must be sharp and have the correct angles on the top face and the front face. Two thousandths of an inch gap between reel and bed-knife is ideal in Northern Europe, but will need to be reduced by half on some exotic or desert grass species.
It is important to maintain the sharp edge on the front of the bed-knife, with a facer or a good file, in order to cut cleanly without bruising the grass. This will also enhance the definition of stripes on the green, thereby improving the after cut appearance and keeping the pace consistent on greens all day during competitive play.
Experiences at Celtic Manor
We have eight Toro 5410 fairway mowers, five were purchased in 2007 and three in 2008. We do not backlap in favour of grinding because it’s quicker using our spin grinders.
The 2007 machines have been sharpened twice, the first time to see how long it took two men to grind five machines during the average work period in peak season (7 hours). Using a calculator it’s easy to see that: 7 hours = 420 minutes divided by 25 cutting units = 16.8 minutes per unit. The time started from driving in the first machine to driving out the last one. This included removing the bed bar, grinding the bed-knife on the top edge and front face, adjusting the height of cut post grinding, and greasing each unit before refitting it to the machine. The technicians carry out all bed-knife
to reel adjustments, we set-up all of our units with no contact at all and the quality of cut is first class.
During tournaments, we give every pedestrian greens mower a very quick spin each time they are used, this takes around five minutes per machine and includes a couple of passes with our Rapid Facer to ‘freshen’ the bed-knife front face, and make fine adjustments to the height of cut.
This is a ‘belt and braces’ measure,
purely for tournaments, because of the limited time for course set-up before the first tee-offs, the mowers must go out in “perfect” condition.
Some figures for you to consider;
From independent field trials we know that, when running a five unit fairway mower set with zero contact, the hydraulic pressure will be around 900lbs, causing minimum mechanical stress to the machine.
Running the same mower set with light contact, but with reels easily turning, the hydraulic pressure will increase to 1800lbs. Because the reel and bed-knife contact begins to act like a brake, as reels get hotter and begin to expand slightly, more heat or heavy contact will increase the braking effect still further. Due to this braking effect of running
reels with light contact, the mower’s fuel consumption will increase by 25 to 30%, the transmission oil and engine oil temperatures will be raised, producing extra stress on hydraulic hoses, motor seals and reel bearings, the risk of oil leaks will increase, reel and bed-knife wear will be much higher and quality of cut will deteriorate rapidly. Professional hydraulic mowers have built in safety relief systems (similar to 3 point tractor lifts), which will release pressure when the hydraulic system reaches about 3,000lbs. This means that any heavy reel and bed-knife contact will begin to open the safety valves and risk causing the hydraulic safety system to bleed off pressure and, so, reduce the efficiency of the mowing unit or stall the cutting units entirely. Remember that the way you set-up, maintain and use your equipment will change the performance and useful life of your mowing machines. It will also effect your manufacturer’s reputation and warranties. Reducing the wear and tear on your machinery, and always setting your mowers with a perfect zero contact cut, will enhance your own reputation and, by providing consistent, high quality playing surfaces, you will ensure that your members and paying customers want to return again and again. Do your own ‘zero contact’ cutting trial today. It may change your life.
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82 |
Page 83 |
Page 84 |
Page 85 |
Page 86 |
Page 87 |
Page 88 |
Page 89 |
Page 90 |
Page 91 |
Page 92 |
Page 93 |
Page 94 |
Page 95 |
Page 96 |
Page 97 |
Page 98 |
Page 99 |
Page 100 |
Page 101 |
Page 102 |
Page 103 |
Page 104 |
Page 105 |
Page 106 |
Page 107 |
Page 108 |
Page 109 |
Page 110 |
Page 111 |
Page 112 |
Page 113 |
Page 114 |
Page 115 |
Page 116 |
Page 117 |
Page 118 |
Page 119 |
Page 120 |
Page 121 |
Page 122 |
Page 123 |
Page 124 |
Page 125 |
Page 126 |
Page 127 |
Page 128 |
Page 129 |
Page 130 |
Page 131 |
Page 132