TOP FIVE CABLING PROBLEMS
Installers should take notice of the minimum bend radius of cable recommended by the manufacturer.
FAMOUS FIVE
DR JEREMY HODGE, CHIEF EXECUTIVE OF THE BRITISH APPROVALS SERVICE FOR CABLES (BASEC), DISCUSSES THE TOP FIVE PROBLEMS ELECTRICAL CONTRACTORS ASK ABOUT WHEN DEALING WITH ELECTRICAL CABLES AND OFFERS ADVICE ON WHAT TO DO IF A PROBLEM IS IDENTIFIED.
1. CABLE DAMAGED DURING INSTALLATION
Armoured cables are intended for use in tough environments such as burial, but they can be damaged during installation. The highest risk is during the process of pulling cable into buildings, particularly over complex routes. The external cable sheath can be scored by a sharp edge such as a cable tray end or even a screw or bolt, and leave a longitudinal groove that can result in later splitting of the sheath. Installers should check for sharp edges before pulling cable. Pulling in cable from a central point, in two directions, can sometimes result in twists or kinks in the cable, and this can result in bulging or displaced armour wires. Installers should take care not to introduce twists or kinks into cable as it
36
comes from the drum, particularly as it passes around rollers.
Installers should take notice of the minimum bend radius of cable recommended by the manufacturer, both in the installation process and in cable tray design and layout. Finally, the unterminated ends of armoured cables should be protected by end caps until terminated.
2. CONDUCTOR RESISTANCE
BASEC has issued a number of warnings to the electrical trade of cables that, when tested through BASEC’s independent testing laboratory, indicate excessive conductor resistance. Some conductors have been found to have up to two standard sizes smaller than
that marked on the cables, which could result in overloading and overheating in use. End users are encouraged to check purchase documentation, design specifications and test their installation to ensure that the applied loading and earthing are acceptable. Findings should then be recorded in documentation. For peace of mind, look for the BASEC mark on the cable sheath, and on the drum or reel which proves it has been independently tested.
3. FAILING SMOKE FOR FIRE TEST
To describe a cable as Low Smoke Halogen Free (LSHF) it must pass two tests − a smoke cube test, which sets a maximum accumulated smoke density produced when burning the cable with a
standard fire, and a corrosive and acid gas test where the cable materials are roasted and must give off a maximum of 0.5 per cent acid gas. These tests are both specified in cable standards which include the description ‘having low emission of smoke and corrosive gases when affected by fire’. Cables made from PVC or similar halogenated materials are unlikely to pass these tests. In terms of market practice more people
are specifying and using LSHF cables. However this does not mean that these cables are fire resistant. For example, for fire fighting lifts and smoke extraction systems, robust fire resistant cables are needed to continue to work in a fire. For this you need special fire resistant cables such as BS 7846 armoured cable or mineral cable to BS EN(IEC)60702-1.
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48