Feature sponsored by Flow, level & control
BASIC VS. PRO SERIES RADAR: WHICH IS THE RIGHT CHOICE FOR YOU?
Basic Series is a lower priced, very capable sensor. The intent of this piece is to explain why one would choose one over the other.
V SPECIFICATIONS
The simplest reason to use a Pro Series device instead of a Basic Series is that the Basic Series sensor does not meet the requirements of the installation. This could be something as simple as the temperature and pressure of the vessel in which the sensor is to be installed. The Basic Series has a temperature range of -40°C to 80°C and a pressure range of full vacuum up to 43.5 psi. If the temperature and pressure are outside of this, then the Pro Series may meet the needs (-196 °C to 450°C full vacuum up to 2,320 psi). There are some certifications that are only available in the Pro Series. Functional Safety (SIL) and cyber security (IEC 62433) certifications are two of these. While both the Pro and Basic Series devices can be used in electrically hazardous areas, only the Pro Series is available with explosion proof as the protection method. While 4…20 mA/HART is the most common output that is used for Pro and Basic Series radars there are some outputs that are unique to each. For instance, SDI-12, which is used in the Hydrologic market is available exclusively in the Basic Series.
MATERIALS OF CONSTRUCTION The Pro Series has many more options when it comes to the materials of construction and wetted parts. The Pro Series offers plastic, stainless steel, and aluminium housings. Stainless steel, Hastelloy C, Duplex, Monel, PFA, PTFE, PEEK and other materials are available as wetted. The Basic Series has PVDF wetted parts and a plastic housing. Installations in which PVDF is not acceptable require the use of the Pro Series. From a mechanical ruggedness standpoint, the Basic Series is constructed of all plastic parts while the Pro-series has metal process connections, antennas, and housings available.
MEASUREMENT PERFORMANCE The Pro Series Radar has advantages when it comes to measuring performance. It is more accurate (+/- 1mm vs +/- 2 mm or 5mm). It is also slightly faster as it updates the output once every 200ms as opposed to once per 250ms. The Basic Series has a measurement range limit
70
EGA has a lot of choices when it comes to radar level measurement devices. In general, there are two families of sensors from which to choose, the Pro Series and the Basic Series. The Pro Series is a full-featured sensor. The
of 30 meters. The Pro Series can measure as far as 120 meters. Overall, the Pro Series is faster, more accurate, and can measure further.
OTHER AVAILABLE FEATURES The Basic Series is limited in its available antennas. The Pro Series has larger antennas available, with a narrower beam, as well as smaller antennas available for mounting in small vessels with small process connections. The Pro Series has a version specifically designed for use in solids. It has a swivel mount integrated into the mounting flange. This allows one to aim the measurement to the position in the silo that provides the most useful measurement. In other words, it could be on the high end near the
position directly underneath the fill or the low side when directly above the emptying point. This version also has an air purge which can help with preventing build-up on the antenna. The Basic Series radar has an available version with a submersible (IP68 3 bar, 24 h) housing and integral cable. This would be the first choice of sensor it if were to be mounted in an area, like a lift station or sump, where it is possible to become covered in water. While it is not usually one of the factors that goes into choosing which radar to use, the Pro Series radar has an entire suite of diagnostic tools that are not available in the Basic Series. These include on board trending, echo curve recording, event memory with real time clock, and a host of others. These can be very useful when tackling difficult measurements or diagnosing customer process problems.
CONCLUSION
VEGA has radar sensors that can perform in many demanding environments including extreme heat and cold, high pressure, chemically corrosive, and potentially explosive. However, there are times when having this capability is not needed. That is when the Basic Series radar should be used. The Basic Series allows one to enjoy all the benefits of radar, without having to pay for features that are either not wanted or not needed. At the same time, there are some environments that require some one or more of the features offered by the Pro Series. In general, it is recommended to use the sensor that will perform the job and survive the environment, providing a long-term, economical solution.
VEGA Controls
www.vega.com October 2024 Instrumentation Monthly
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82 |
Page 83 |
Page 84 |
Page 85 |
Page 86 |
Page 87 |
Page 88 |
Page 89 |
Page 90 |
Page 91 |
Page 92 |
Page 93 |
Page 94 |
Page 95 |
Page 96
