search.noResults

search.searching

saml.title
dataCollection.invalidEmail
note.createNoteMessage

search.noResults

search.searching

orderForm.title

orderForm.productCode
orderForm.description
orderForm.quantity
orderForm.itemPrice
orderForm.price
orderForm.totalPrice
orderForm.deliveryDetails.billingAddress
orderForm.deliveryDetails.deliveryAddress
orderForm.noItems
LARGE-FORMAT TILES WHAT THE CERAMIC SURFACES INDUSTRY CAN DOCUMENT


The most solid basis is third-party-verified data. The sector- wide environmental product declaration (EPD) for Italian ceramic tiles, drawn up under EN 15804 and verified by an independent programme operator, represents 74 companies and 87 plants, equal to 82.6% of Italian production. For one square metre of average installed tile (1cm thick, 21.38 kg/m²), it gives a global warming potential for the production stage (A1–A3) of 11 kg CO² equivalent. It is valid from 4 January 2023 to 3 January 2028 and is based on primary data from 2020. Two caveats apply: it is an average across thicknesses from 3 to 30mm and across all tile types, so it is not a figure for slabs, and to assess a specific slab the manufacturer’s product EPD is preferable, because weight, thickness, composition and production process can change the impact significantly. Since June 2024 the Italian trade association Confindustria Ceramica has also made available to its members an updated, pre-verified EPD Tool, able to account for the mesh applied to some ceramic products. The international standard ISO 17889- 1:2021 adds a framework for assessing the sustainability of ceramic tiles beyond carbon.


The Italian trade association also reports, through its annual integrated environmental report, a detailed measurement of more than 35 environmental indicators, including emissions, management of process waste and water, and energy. According to the 2024 report, 11.2% of the sector’s raw materials are pre-consumer recycled material (ISO 14021), 100% of internal production waste is recovered and 48% of the water required comes from internal recycling: these are averages across all tiles, not data for slabs. On energy, the sector cites cogeneration, heat recovery from kilns, photovoltaics and digital monitoring, while decarbonising firing remains an open challenge.


WHAT IS SPECIFIC TO THE SLAB FORMAT


A material made from natural raw materials and fired at high temperature is inert once installed and does not burn. These properties, together with durability and a service life of over 50 years, matter in a whole-life assessment because the use phase is long: the longer a surface performs without being


replaced, the more its initial impact is spread over time. Durability, however, must be assessed within the whole-life analysis and not used on its own as proof of lower impact: the sector EPD, for example, does not report the reference service life provided for by ISO 15686. For slabs, five points are relevant.


Less mass per square metre: Where the average thickness of a ceramic slab, 8–10 mm, is reduced even threefold, a thinner slab uses less raw material and, in principle, requires less energy for firing and less weight to transport. Thinner is not automatically more sustainable, however: reinforcement (such as mesh), processing, durability, scrap and application also matter. How much less depends on thickness, product and manufacturer: for this reason, comparisons require product EPDs calculated under the same rules, not averages.


Process efficiency: Technology suppliers point to advantages of continuous compaction, such as lower hydraulic oil use and low compaction scrap, which can be recycled; these are supplier claims about individual stages and do not concern firing, where most of the energy is concentrated. Manufacturers also report that digital decoration reduces water and auxiliary materials compared with traditional decoration: the saving should be requested as measured data. Circularity in production must also be distinguished from circularity on site: cutting and installation offcuts of slabs depend on design and installation, not on the production-waste recovery data.


Fewer joints, more uses: Continuous surfaces allow a single material for floors, walls, worktops and furniture. Whether this reduces the overall impact of a project depends on the alternative being replaced and on installation losses, and must be assessed at project level.


Secondary raw materials: For slabs, no sector-level data on recycled content are available among the verified sources: the figure cited above covers all tiles. Research is studying mixes with secondary raw materials and production scrap: Centro Ceramico projects such as WINCER (2015–2017) have developed mixes with at least 60% end-of-waste materials, but on standard formats.


Transport and installation: The lower weight of some slabs can benefit logistics, but the overall impact depends on weight, distance, transport mode, packaging and installation. Handling, cutting and laying are also more complex: The Tile Association points to dedicated frames and suction cups, flat substrates (at least SR1) and class C2 S1 or S2 adhesives, and mistakes generate offcuts.


OUTLOOK


Large slabs are likely to keep gaining ground where continuity, realism and versatility matter, and the design signals for the coming seasons all point this way. Suppliers’ commercial advantage will increasingly lie in their ability to show verifiable data: product EPDs, clear boundaries and an honest account of what is a measured result and what is work in progress. For specifiers and distributors, the most useful request is a simple one: ask for the declaration behind the claim.


www.ceramica.info x.com/TomorrowsTS 29


Page 1  |  Page 2  |  Page 3  |  Page 4  |  Page 5  |  Page 6  |  Page 7  |  Page 8  |  Page 9  |  Page 10  |  Page 11  |  Page 12  |  Page 13  |  Page 14  |  Page 15  |  Page 16  |  Page 17  |  Page 18  |  Page 19  |  Page 20  |  Page 21  |  Page 22  |  Page 23  |  Page 24  |  Page 25  |  Page 26  |  Page 27  |  Page 28  |  Page 29  |  Page 30  |  Page 31  |  Page 32  |  Page 33  |  Page 34  |  Page 35  |  Page 36