LARGE-FORMAT TILES THE BIGGER PICTURE
From kitchen worktops to continuous floors, large slabs have moved from showpiece to mainstream product. As specifiers demand proof rather than promises, attention is turning to how slabs are made and the environmental claims manufacturers can substantiate, says Ceramics of Italy.
Large slabs are used both in architecture and interior design and as a complement to furnishings. This latest application, the most recent, has more limited volumes.
WHERE THE MARKET IS HEADING
Large slabs belong to a sector that is stable rather than booming. In 2025 Italian manufacturers produced 390.9m square metres of ceramic tiles (+5.7% on 2024) and sold 386.9m (+2.3%), of which over 301m abroad. Turnover was €6,041m (−0.4%), 82% of it generated by exports, and porcelain stoneware accounted for 93% of production. These are the national statistics published by Confindustria Ceramica and they cover all ceramic tiles.
These signals are consistent. The Spring-Summer 2026 Ceramics of Italy Trend Report points to large slabs growing in kitchens, as worktops paired with integrated induction hobs, and in dining tables and fireplace surrounds. In the UK, an industry article from July 2025 named 30×60, 60×60 and 60×120cm as the best-selling formats, with 120×240cm seeing ‘steadily’ growing popularity with residential and commercial clients.
On the design front, Italian manufacturers interviewed ahead of Cersaie describe warm colours and stone effects, less interest in full-field gloss finishes and a mix-and-match approach, in which collections are no longer sold as closed, vertical ranges. The main technical innovation, they say, is digital printing enriched with digitally applied materials, glazes and textures, for extreme realism. Design printing adds coloured and dark marbles, a ‘total look’ across floor, wall and furniture, and biophilic projects. These are design observations rather than market measurements, but they point in the same direction: continuity of surface, realism and fewer joints.
HOW A SLAB IS MADE
Large formats come from two production routes. Traditional dry pressing of powders reaches about 240cm; continuous compaction on a powder bed, as Ingenio describes, goes further, up to 180×600cm, compacting a bed of powder of fixed width between rollers and cutting the slab before or after firing. Digital powder loading and digital decoration allow veining to run through the thickness, and grinding and lapping can add functional finishes such as slip resistance. Thicknesses range from about 3 to 20mm: the thinnest for wall cladding, worktops and furniture, the thickest for floors and surfaces under heavy loads.
WHY SUSTAINABILITY EVIDENCE MATTERS NOW
Specifiers are being asked for numbers. In the UK, proposals such as the so-called Part Z would require whole-life carbon to be assessed and reported for the largest projects; this is still a
28
proposal, so the practical point is the direction of travel: projects increasingly need product data to feed into an assessment. At the same time, the rules on how environmental benefits may be described are tightening. Since 6 April 2025 the Competition and Markets Authority (CMA) can fine companies directly up to 10% of global turnover for misleading consumer claims under the Digital Markets, Competition and Consumers Act, and in the EU the Empowering Consumers Directive (2024/825), which bans generic environmental claims without proof and offset-based neutrality claims, applies nationally from 27 September 2026. For a supplier or distributor, a generic ‘eco-friendly slab’ is now a risk; a verifiable figure is an asset.
The same direction can be seen in Europe, as an indicator of regulatory direction rather than as UK law. The EU Energy Performance of Buildings Directive (2024/1275) requires the life cycle global warming potential (life cycle GWP) of new buildings to be calculated and reported in the energy performance certificate, from 2028 for buildings above 1,000 m² and from 2030 for all new buildings, using the common methodology set out in Delegated Regulation (EU) 2026/52 (European Commission). The new Construction Products Regulation (EU) 2024/3110 aims at greater availability and interoperability of digital product information, including the Digital Product Passport: a trend towards material transparency, not a general obligation in the UK. Finally, in Italy, the new Minimum Environmental Criteria for construction – mandatory in Italian public procurement from 2 February 2026 – provide for simplified procedures for life- cycle assessment (LCA): this is an Italian rule, not a UK one, cited as an example of the broader shift towards assessing performance across the whole life cycle.
www.tomorrowstileandstone.co.uk
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36