WETROOMS
WATERTIGHT WETROOMS
Palace Chemicals outlines key considerations for tanking, tiling and finishing wetroom installations.
The Palace Chemicals range of wetroom products has been developed to ensure that wet areas are fully waterproofed (tanked), and also to help tilers achieve a successful installation. Key products include the PALACE SHOWER- TIGHT kit. This is a waterproof barrier system, developed to protect sensitive substrates in tiled areas such as showers, bathrooms, wetrooms and kitchen utility areas. It is a complete kit, ideally suited for tanking a single shower cubicle or an over-bath shower.
The system consists of a 1 litre primer, 2.5 litres grey flexible latex waterproof coating, 1 square metre super strong polyester mat, complete with 10 metres of polyester tape to reinforce seams in joints around wall/floor junctions along with all corners. This seamless, protective membrane inhibits the passage of moisture from within the tiled area through to surfaces and structures which may be sensitive to the effects of prolonged water migration. In total it provides 4 square metres coverage.
“PALACE AQUABAN WILL PROVIDE A COMPLETE
WATERPROOF BARRIER BEHIND THE TILED AREA.”
If a full wet-room installation is being undertaken, then PALACE AQUA-BAN is the best product to use. This is a waterproof membrane system designed to protect tiled areas in locations such as wetrooms, commercial or domestic showers, bathrooms, and swimming pools. PALACE AQUA- BAN will provide a complete waterproof barrier behind the tiled area, for use on all types of substrates such as plaster, render, plasterboard, tile backer boards, suspended floors, concrete floors and overlays.
This is a 7kg, grey flexible latex waterproof coating (and is also available in larger commercial sizes), that has the ability to bridge cracks or joints less than 3mm, bond to plastic and metal and replicate the weight loading capabilities of the receiving substrate without the use of an additional primer.
To ensure a complete system approach, the PALACE AQUA- BAN SEALING KIT should also be used, which consists of two rubber/polyester pipe covers and a 10-metre length of elastomeric reinforcing tape to reinforce seams in joints around wall/floor junctions where the gaps are larger than 3mm. Using the full system also gives added peace of mind
16
www.tomorrowstileandstone.co.uk
as it conforms to the relevant European EAD requirements. The overall coverage is 7-8 square metres and can enable tiling or flood testing around two hours after installation.
The built-in flexibility of both systems will accommodate a level of movement and vibration, providing a solvent-free base for fixing wall and floor tiles. Both types of reinforcing tapes provide crack-bridging protection for all wall and floor joints. Both systems also boast the ability to tile over or flood test in just two hours.
When it comes to the tiles themselves, there are a wide range of ceramic tiles, conforming to the requirements of BS EN 14411, that may be used in a wet room. Glass and ceramic mosaics, as well as natural stone tiles can also be used. Some agglomerated natural stone tiles can suffer discolouration in a wetroom environment and alternatives such as glazed or unglazed porcelain or fully vitrified ceramic tiles can also be used, provided they conform to the relevant British Standard. For floors a suitable non-slip tile should be used, since trips and slips in bathrooms and wetrooms are a major cause of injury.
Adhesives used to fix tiles over tanked surfaces should be water-resistant and suitable for wetroom installations. For floors the tile adhesive should be compatible with underfloor heating systems, if one is included in the installation. Ideally a cement-based product classified as EN12004 C2 (such as PALACE MULTI-FLEX or EASI-FLEX) will provide the most reliable bond to tanked surfaces in areas when subject to frequent wetting.
When it comes to grouting, a CG2 cement-based grout should be used, such as PALACE ANTI-MOULD or COLOUR-LOCK GROUT, which are both water repellant – with the latter being efflorescence-resistant. Ideally this should include an anti-bacterial additive to prevent the development of black spot mould. Epoxy grouts can also be used to provide a higher level of water and stain-resistance, such as the COLOUR-GUARD PRO, which is a gamechanging 3-part maintenance-free system.
www.palacechemicals.co.uk
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36