WHERE THERE’S WATER...
Jason Tatton, one of F. Ball and Co. Ltd.’s technical service officers, discusses the variables to consider when determining how to make resilient flooring installations resistant to moisture, including new alternatives to traditional solutions.
Water that is allowed to get beneath resilient floorcoverings can attack adhesives, causing floorcoverings to blister and de-bond and damage subfloors that are sensitive to moisture, such as chipboard. Ultimately, this may result in costly floor failure and recalls. Key to preventing floor failure in these situations is using suitably moisture-resistant adhesives and floorcoverings (which depends on how much water they will be exposed to) as well as proper subfloor preparation.
SUBFLOOR PREP As with any floorcovering installation, appropriate subfloor preparation is imperative to ensuring a longlasting, professional flooring finish and avoiding floor failure.
Before installation, make sure that the subfloor is suitably sound, smooth and free of any surface contaminants, including old adhesive residues and non-moisture tolerant smoothing underlayments and primers.
In accordance with British Standards, we recommend the use of a pre-calibrated digital hygrometer to measure the relative humidity (RH) levels within the subfloor as part of any floorcovering installation. If subfloor relative humidity levels exceed 75% RH, a waterproof surface membrane will be required.
FLOORCOVERINGS Resilient floorcoverings are an obvious choice for damp and humid environments because they create a barrier between the subfloor and the damaging effects of moisture.
Vinyl planks or tiles may be installed in humid environments, such as domestic bathrooms. However, the installation of vinyl sheet is recommended in wet rooms and other areas where floors will be subject to high levels of moisture, including standing water. In these situations, seams must be welded to ensure a watertight seal and prevent an ingress of water. For the same reason, there should be seals where floorcoverings meet drains or capping and coving at walls.
In any case, floorcoverings and vertical flooring accessories should be installed using a suitably moisture-resistant adhesive.
ADHESIVE SELECTION Epoxy or polyurethane adhesives have traditionally been
twitter.com/TContractFloors
the recommended option for making flooring installations impervious to water, inside and outdoors because of their high resistance to water, oil and grease.
The latest advancements in adhesives technology have enabled F. Ball to create a one-part, moisture-curing adhesive for internal and external heavy-duty applications, which is also solvent and isocyanate free: Styccobond F73 PLUS.
The adhesive has been specially developed to provide the high bond strength required to hold a wide range of floorcoverings in place in the most demanding environments, such as in areas subject to surface water, heavy loads and high foot traffic, including in transition areas and entranceways. Unlike reactive adhesives, the adhesive offers high initial grab, and fibres in the adhesive limit lateral movement of floorcoverings while contractors are working.
Styccobond F73 PLUS is also easier to apply and faster curing than traditional alternatives, requiring as little as 90 minutes to secure floorcoverings. The adhesive can be trowel-applied to a wide variety of sound, smooth absorbent subfloors, including concrete and sand/cement screeds, and its fast- setting properties allow welding of sheet floorcoverings to take place from as little as two hours.
ANOTHER SOLUTION The arrival of hybrid adhesives, such as F. Ball’s Styccobond F49 Hybrid PS, provided another solution for installing resilient floorcoverings in damp and humid environments. As well as being resistant to water, Styccobond F49 offers the familiar characteristics of pressure sensitive adhesives, making it ideal for LVTs. It also develops the extremely high bond strength to hold floorcoverings in place in areas exposed to extreme temperature fluctuations.
Excellent resistance to plasticiser migration and high initial grab also makes Styccobond F49 an alternative to contact adhesives for installing vertical flooring accessories, including skirting, capping and coving, which are typically applied to vertical surfaces that may be subject to damp and humid conditions.
www.f-ball.com TIP OF THE MONTH | 13
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54
