GRAND DESIGN F. Ball’s System LVT range delivers on an ambitious self-build project.
Products from F. Ball and Co. Ltd.’s System LVT range, including the company’s fast-track, fibre-reinforced transitional adhesive, Styccobond F58 PLUS, have been used to install luxury vinyl tiles in an ambitious, modern self- build property in rural Cambridgeshire.
Contractors from 4 Floor Fittings began by thoroughly vacuuming the building’s concrete subfloor to remove dust and debris. F. Ball’s technical service team recommended treating the subfloor as a newly installed screed for the purposes of moisture management, despite being installed months earlier, as it had been left exposed to the elements since. Therefore F. Ball’s Stopgap F77 waterproof surface membrane was used to create a barrier to prevent excess subfloor moisture attacking adhesives and floorcoverings, potentially causing floor failure.
Once the waterproof surface membrane had cured, the surface was primed using F. Ball’s primer for use over non- absorbent surfaces, Stopgap P141. The company’s Stopgap 300 HD heavy-duty levelling compound was then applied over the entire ground floor to create a perfectly smooth base for the receipt of floorcoverings. The product’s high compressive strength and excellent self-levelling properties help create a flawless finish when installing LVTs, while ensuring a long-lasting, aesthetically pleasing floor finish even when subject to high levels of wear.
“Styccobond F49 was
used where floor-to-ceiling windows were likely to cause
temperatures to rise significantly as a result of solar gain.”
The contractors then used Styccobond F58 PLUS and F. Ball’s Styccobond F49 Hybrid PS temperature tolerant, moisture resistant, pressure sensitive adhesive to install wood-effect LVTs over the 372m2
area. Styccobond F49 was used where
floor-to-ceiling windows were likely to cause temperatures to rise significantly as a result of solar gain. The adhesive will hold floorcoverings firmly in place when subject to extreme temperatures and temperature changes (from -20°C and up
24 | RESILIENT FLOORING
to +60°C), which can cause floorcoverings to expand and contract significantly, leading to tenting and gapping at the edges of LVTs over time.
Styccobond F58 PLUS was used to install vinyl tiles everywhere else. The fast-track adhesive enables floorcoverings to be installed from as little as five minutes after application, transitioning from a wet-lay adhesive to become fully pressure sensitive. Reinforcing fibres in the formulation provide resistance to lateral movement, holding tiles firmly in place and reducing the potential for them to slide around when working. The adhesive’s high bond strength and strong initial tack also prevent excess adhesive oozing between joints, facilitating easier application.
All of the products used in this installation feature in the company’s System LVT range: subfloor preparation products and adhesives which, used in combination, can help achieve optimum results when installing LVTs.
Commenting on the project, Richard Argyle of 4 Floor Fittings, said: “It’s the best screed I’ve ever done. The levelling compound had no imperfections whatsoever. Styccobond F58 PLUS allowed floorcoverings to be installed over large areas in one go while helping with the precise alignment of LVTs. The result is a visually striking finish in keeping with the rest of the project.”
www.f-ball.co.uk
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50
