INSIGHT
safety programmes. “Safety is a huge factor for us,” says Steinbock. “Alternative methods require equipment which can create extremely dangerous conditions. Our products are safe to use, and this is a huge benefit to our customers.” While Superbolt products are available
off-the-shelf, about half its sales are for special non-standard items in sizes all the way from M16 to over M1450. “What makes Superbolt unique is our ability to adapt to different situations, whether this is reviewing temperatures and changing materials, or customising designs to fit customer requirements. We are very adaptable and want to make sure that the customer receives the right solution and is satisified,” says Busalacchi. Users of Superbolt products including
General Electric, Siemens and Rolls-Royce appreciate the fact that that they can receive finite element analysis (FEA) carried out by independent organisations. “These organisations can provide an independent assessment of what we are telling our customers about our calculations,” says Norbert Schneider, head of engineering at Nord-Lock AG. “It boils down to safety and customers’ peace of mind.” A current installation of Superbolts
shows just how extreme an environment they can handle. About 2,000 tensioners made from exotic nickel-based alloys
Gold award from CERN Superbolt supplied more than 1,500 high-strength mechanical tensioners, expansion bolts and multi-jackbolt tensioners to the CERN Large Hadron Collider in Switzerland. Multi- jackbolt tensioners were used for an application requiring a very high clamping force, but with limited space for tightening the bolts. Since only hand tools were required, the need to create anchor points for heavier tightening equipment was eliminated. Superbolt won the CMS gold award for its contribution to the project.
have been installed at the Max Planck Institute for Plasma Physics in Greifswald, Germany, where research will be carried out into the principles of a fusion power plant, which, in the future, could provide safe, green energy from the same process that takes place inside the sun. “The Max Planck Institute has chosen
Superbolt because the ambient conditions under which the research is to be carried out are quite horrendous - we are talking about -270°C, radiation and an absolute vacuum, as well as extremely high loads,” says Schneider. “Basically, we are dealing with outer space conditions found close to the sun.” And highly compact machines mean that there is no access for heavy tools. “The forces are so immense that they require large bolts and the only way to tighten large bolts without heavy tools is the Superbolt principle,” says Schneider. Such characteristics and performance
mean that once customers have tried Superbolt, they rarely return to the troublesome methods of the past. “The hardest part, as with any product,
is to get people to try it,” says Steinbock. “But once people have tried it, our repeat order rate is phenomenal. Customers now count on us to provide a quality product and we receive tremendous loyalty from them in return.”
Benefits of Superbolt include: • Only hand tools are required. • Time and labour saving. • Maximum holding power. • Increased workplace safety. • Accurate preload. • Ideal for restricted areas. • Flexing adds elasticity to the joint. • Tightens in pure tension. • Economical and reusable.
Superbolts in use: Ideal mine solution The severe environment of an
underground coal mine takes a brutal toll on crusher drum bits. It is a violent application with high RPMs and constant pounding as the bits cut into coal and rock and often break off, requiring repair underground, where accessibility is limited. With Superbolt, space restrictions are of little concern because only small hand tools are required, making the process easier and faster.
Cheaper and faster Large ammonia reactors often require
the use of large and expensive hydraulic tensioners, and tightening or untightening can take several days, working around the clock, and using cranes. At one such reactor, not only was the initial cost of the Superbolt tensioners only a fraction of the cost of the hydraulic tensioners they replaced, but the installation took two labourers only 5 hours.
62 Fastener + Fixing Magazine • Issue 75 May 2012
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82 |
Page 83 |
Page 84 |
Page 85 |
Page 86 |
Page 87 |
Page 88 |
Page 89 |
Page 90 |
Page 91 |
Page 92 |
Page 93 |
Page 94 |
Page 95 |
Page 96 |
Page 97 |
Page 98 |
Page 99 |
Page 100 |
Page 101 |
Page 102 |
Page 103 |
Page 104 |
Page 105 |
Page 106 |
Page 107 |
Page 108 |
Page 109 |
Page 110 |
Page 111 |
Page 112 |
Page 113 |
Page 114 |
Page 115 |
Page 116 |
Page 117 |
Page 118 |
Page 119 |
Page 120 |
Page 121 |
Page 122 |
Page 123 |
Page 124 |
Page 125 |
Page 126 |
Page 127 |
Page 128 |
Page 129 |
Page 130 |
Page 131 |
Page 132 |
Page 133 |
Page 134 |
Page 135 |
Page 136 |
Page 137 |
Page 138 |
Page 139 |
Page 140 |
Page 141 |
Page 142 |
Page 143 |
Page 144 |
Page 145 |
Page 146 |
Page 147 |
Page 148 |
Page 149 |
Page 150 |
Page 151 |
Page 152 |
Page 153 |
Page 154 |
Page 155 |
Page 156 |
Page 157 |
Page 158 |
Page 159 |
Page 160 |
Page 161 |
Page 162 |
Page 163 |
Page 164