STERILE PROCESSING INSIGHTS by Stephen Kovach
SUBMIT YOUR QUESTIONS:
editor@hpnonline.com
To be hand in glove with safe practices
As with any practice, and especially with gloves, facilities should have a standard way of donning gloves at their facility based on standards, guidelines and the glove manufacturers’ instructions for use (IFU). There are a set of “Best Practice Common Steps” that should always be followed no matter where you are don- ning gloves. 1. Wash hands with soap and water for 20 seconds before putting on gloves.
Q A
2. Close the proper glove for the task at hand from the inventory provided. a. ear properly fi tting gloves with a close fi t around fi ngers and wrists to reduce the risk of exposure.
b. If wearing any type of gown, make sure the gloves extend at least over the cuff of the gown.
3. Never reuse or wash single-use or exam gloves.
4. Never use damaged or visibly soiled gloves.
5. Do not touch your face while wearing gloves.
So, from the information in your question, I would say yes, the person did not follow this best practice for donning gloves.
I saw a staff member donning his gloves for work in decontamination
not wash his hands. Is this the correct practice?
When we talk about gloves, there is a lot of guidance to be reviewed. We need to look at least to the FDA, ANSI/ AAMI, OSHA, and ASTM standards and guidelines to answer your question. The type of glove that a staff member uses should be based on the type of proce- dure to be performed (e.g., surgical versus nonsurgical or housekeeping procedures). Medical-grade nonsterile examination gloves and sterile surgical gloves are medi- cal devices regulated by the U.S. Food and Drug Administration (FDA). The FDA does not regulate general-purpose utility gloves because they are not promoted for medical use. Sterile surgical gloves must meet standards for sterility assurance estab- lished by the FDA and are less likely than nonsterile examination gloves to harbor pathogens that may contaminate an opera- tive wound. 1
Q A
When we review information in ANSI/ I ST, it does not get specifi c with a stated thickness. The standard instead gives characteristics that gloves should have for working in decontamination. The term for this type of glove is a utility glove. tility gloves should be fi tted at the wrist, prevent contact of the wearer’s skin with contaminated water, and have cuffs that extend beyond the gown’s cuff. It also states that a medical examination glove should not be used in decontamination, as it is not puncture- or cut-resistant. I would suggest that the facility decide on glove thickness by performing a risk assessment. Consider things like the type of tasks staff perform, how dexterous people need to be, and the risk of exposure to help decide on the thickness of gloves.
Photo courtesy: Stephen Kovach
With Occupational Safety and Health dministration SH, we fi nd the fol lowing statements backing up the assess- ment approach to selecting adequate glove thickness and design.2 • 1910.138(a) - General requirements. Employers shall select and require employees to use appropriate hand protection when employees’ hands are exposed to hazards such as skin absorp-
32 May 2021 • HEALTHCARE PURCHASING NEWS •
hpnonline.com
Is there a thickness that gloves need to be for working in decontamination?
tion of harmful substances; severe cuts or lacerations; severe abrasions; punctures; chemical burns; thermal burns; and harm- ful temperature extremes.
• 1910.138(b) Section. Employees shall base the selection of the appropriate hand protection on evaluating the per- formance characteristics of the hand protection relative to the task(s) to be performed, conditions present, duration of use, and the hazards and potential haards identifi ed. Gloves, depending on how they are used in medical facilities, have various standards and tests that they need to comply with. Some of them are from the American National Standards Institute (ANSI), which provides a guideline for the selection of hand protection (ANSI/ISEA 105). This guideline gives manufacturers a mechanism to classify their products for specifi ed areas of glove performance. The following American Society for Testing and Materials (ASTM) guidelines also address glove usage. • ASTM D5151, Test Method for Detection of Holes in Medical Gloves
• ASTM F1671, Test method to show gloves’ ability to protect against micro- organisms.
• ASTM F1790, Standard Test Method for Measuring Cut Resistance of Materials Used in Protective Clothing
Thus, facilities should perform a proper risk assessment and involve the staff who will be using the gloves. By doing that, I feel a policy can be implemented to address all the concerns of the proper glove to be used in the decontamination area, including its thickness. HPN
Note: Glove thickness is stated in either mils or gauge. A 10-gauge glove equals 10 mils or 0.010 inches. When choosing your glove, look for the stated thickness on the manufacturer’s test data.
References
1.
https://www.osap.org/page/FAQPPE20154/FAQ---Personal- Protective-Equipment---2015.htm?page=AboutOSAPContact
2.
https://www.osha.gov/laws-regs/regulations/standardnum- ber/1910/1910.138
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52
