Cable Management
Avoiding corrosion – it’s a material choice
When specifying a cable management system, you need to understand the environment in which your customer will install it and advise them about the best material choice. In this article, Paul Nolan, projects director for the Hudson Group, takes a closer look at what factors you should consider.
W
e have all seen cable management and containment systems that suffer the ravages of corrosion because someone selected the wrong material. Equally, there is little point in choosing an unnecessarily expensive material if the system is for an office or similar benign environment.
The first step is to refer to EN ISO 12944-2 which provides classifications for corrosion and examples of where you may find them – see table below.
Choosing the right material Where you have very low corrosivity or C1, you should recommend either electro zinc plated or pre-galvanised steel. This would typically be for an indoor environment such as in an office, school, hotel or shop.
Raising the stakes slightly higher, a low to
moderate C2 corrosive environment might be found in industrial premises, sports halls, warehouses or partially outdoor applications. We would suggest a pre-galvanised steel cable management system. For C3, where there is moderate environmental corrosivity, think outdoors or in a light industrial area, then you need to go beyond a pre-galvanised solution. For these applications think about hot dip galvanised, CPC (Clear Plastic Coated) coated or powder-coated steel or PVC systems.
And when your customer faces a highly corrosive environment, or C4, then they should use hot dip galvanised or powder coated steel, 304L stainless steel, PVC or GRP systems.
For very highly corrosive environments such as chemical or water treatment plants, heavy industry, swimming pools or perhaps dockyards, then they will need a material that will stand the test of time. For this C5-I classification you should suggest 304L
ATMOSPHERIC CORROSIVITY CATEGORIES ACCORDING TO EN ISO 12944-2 WITH INDOOR AND OUTDOOR EXAMPLES OF TYPICAL ENVIRONMENTS
C1 VERY LOW • EXAMPLE INDOOR:
Heated areas with dry air and minor amounts of impurities e.g. OFFICES / SCHOOLS / SHOPS / HOTELS
• EXAMPLE OUTDOOR: N/A C4 HIGH • EXAMPLE INDOOR:
Areas with high air humidity and high atmospheric pollution from production processes e.g. CHEMICAL PLANTS / SWIMMING POOLS / SHIPYARDS
• EXAMPLE OUTDOOR:
Environments with moderate salinity e.g. INDUSTRIAL & INLAND COASTAL AREAS
or 316L stainless steel, deep galvanised steel or GRP. And finally, there is a special classification for marine environments (C5-M), which are notoriously corrosive. Here your customer will need a 316L stainless steel or a GRP system.
Know what you are selling
Even with the above suggestions there are still some things that you should be aware of. One subject that you might hear about is zinc whiskers. These form on the underside of galvanised products or electroplated metals. These thin whiskers can eventually grow up to 1cm in length, break off and become a problem to electronics.
Also, hot dipped galvanised products will have a standard coating of 45 to 65 microns after being dipped in a bath of molten zinc. This is the average coating; the product is not evenly coated along its length. Deep galvanised products use a different steel which allows it to apply a thicker zinc coating for extra protection, but the process is more expensive.
And if a manufacturer tells you that they double dip their products, then ignore them. A steel will reach its maximum zinc absorption after one coating, a second coating will make no difference.
C2 LOW
• EXAMPLE INDOOR: Unheated areas with varying temperature & humidity levels. Low frequency of condensation and low level of atmospheric pollution e.g. SPORTS HALLS / WAREHOUSES
• EXAMPLE OUTDOOR: Environments with low levels of atmospheric pollution e.g RURAL AREAS
C5-I
VERY HIGH (INDUSTRIAL)
• EXAMPLE INDOOR: Areas with almost constant condensation and high levels of atmospheric pollution.
• EXAMPLE OUTDOOR: Industrial areas with high air humidity and aggressive atmospheres e.g. TUNNELS / DOCKYARDS
Different materials and treatments Remember that materials science does not stand still; someone will develop a better solution. One example is a new finish called Magnelis. This Magnesium Zinc alloy finish provides better corrosion resistance than galvanised options, is self- healing for cut edge protection and it is more cost effective.
Aluminium is not new but it provides a lightweight strong option for some applications; however, it can be hard to perforate and add fixing slots to.
C3 MODERATE • EXAMPLE INDOOR:
Areas with moderate air humidity and some atmospheric pollution from production processes e.g. BREWERIES / DAIRIES / LAUNDRIES
• EXAMPLE OUTDOOR:
Environments with low salinity or moderate atmospheric pollution e.g. URBAN AREAS / LIGHT INDUSTRIAL / SOME COASTAL INFLUENCE
C5-M
VERY HIGH (MARITIME)
• EXAMPLE INDOOR: Areas with almost constant condensation and high levels of atmospheric pollution e.g. PURIFYING PLANTS
• EXAMPLE OUTDOOR:
salinity e.g. OIL RIGS
For really extreme environments, GRP, or glass reinforced polymer, is the go-to material. Even here you need to be aware of different characteristics, since the mechanical properties of this material can vary.
It pays to know the basics about different materials and when you should suggest using them, but always remember that you can always phone the manufacturer to ask for their advice.
18 | electrical wholesalerAugust 2023
ewnews.co.uk
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40
