CODING, MARKING & LABELLING FEATURE MARKS OF DISTINCTION
As product traceability grows in importance, manufacturers are increasingly integrating automated component marking systems into their production lines and systems. Several component marking options are available, but which is the best? Alastair Morris of Pryor Marking Technology may have the answer...
series of dots onto the surface of a material. The stylus is programmed to move around the surface, resulting in a succession of dots that create digits, text, logos and 2D data matrix barcodes. Dot peen marking provides fast, accurate,
M
odern manufacturers use
inventory control and asset tracking to support quality and traceability in production. This, in turn, ensures the right parts are used in the correct places and guarantees the accurate, timely identification of affected parts when quality deviations are identified. It can also simplify maintenance and
management activities throughout the working life of the product, helping operations and maintenance staff track failures and match replacement parts. But tracking components requires them
to be marked in some way. Marking methods include manual hand stamps and engraved dies, but the more common methods in industrial applications are lasers, dot peening, chemical etching and scribing. Laser technology (see the panel) is
generally seen on more advanced systems. For many applications, however, this approach can be overly complex or expensive, in which case manufacturers have three main options available.
DOT PEEN MARKING Also known as dot marking, stylus pin marking and micro percussion marking, this component marking method employs a stylus that rapidly punches a
low-stress marking and can mark through coatings or film on the material surface. Dot peen machines can mark a wide range of materials. The angle of the stylus tip may be changed to further reduce the chance of material flaws.
CHEMICAL ETCHING This works by the electro-chemical dissolution and/or oxidation of metal from the surface being marked through a stencil impression to give the required mark. This is achieved by sandwiching a stencil between the surface being marked (connected to the anodic polarity of the etching unit) and an electrolyte soaked pad (connected to the cathodic polarity), and passing a low voltage current between the two. Many electrolyte solutions exist, the
compositions of which may vary according to component material type. However, they are all designed to produce some form of chemical attack of the material. Once the material has been etched, the
electrolyte is neutralised by removing all traces of it from the component.
SCRIBE MARKING A pneumatically-driven pin is driven into the metal surface to be marked. It is then moved through the metal, giving a continuous engraved line to produce the required inscription. Marking machines can mark a wide range of materials, although clearly softer materials will be easier to mark. The harder the material, the shallower the depth of mark will be. The type of material will also influence the life of the stylus. The angle of the stylus tip may be changed to reduce the chance of chipping. Changing the angle may also increase the readability of the mark. Smooth, well finished workpieces are easier to mark than rough, scaled work pieces. The more complex the finish, the deeper the mark will have to be to remain readable. Painted workpieces may be marked but there is the risk that the marking process can cause the paint to chip.
Pryor Marking Technology T: 0114 276 6044
www.pryormarking.com
Shedding light on laser marking T
ypical marking lasers come in three types – carbon dioxide
(CO2), YAG or fibre. The most basic form of a CO2 laser consists of a gas discharge with a reflector at one end, and an output coupler (a partially reflecting mirror) at the output end. CO2 lasers have a high wavelength (operating in the infrared) which makes them a poor choice for metal marking applications because the laser radiation is often reflected by the target material. YAG and fibre lasers have
shorter wavelengths which not only provide better marking resolution, but are also easily absorbed by metal.
/AUTOMATION YAG lasers (also called flash
lamp or lamp-pumped lasers) use a bulb lamp as a pumping mechanism and yttrium aluminium garnet (YAG) synthetic crystal as the gain medium. They are becoming less popular because the bulbs have a short life and the lasers are inefficient – they generate a lot of heat and therefore require a liquid coolant. Solid state fibre lasers have
become the industry standard for reliable, high quality marking. The laser source is sealed, preventing dust and particle contamination. This also enables longer distances between the control unit and the marking head, allowing the laser source to
be situated remotely from the point of use. Furthermore, it reduces leakage, resulting in greater efficiency. Overall, the fibre laser is
cheaper to run and has fewer replacement parts than the YAG laser. The fibre laser is air-cooled, which makes it more compact and easier to integrate into existing systems and processes.
AUTOMATION | JUNE 2018 27
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60
