INTERCONNECTION
What makes a space-worthy connector?
Jonathan Parry, senior vice president and European managing director at cables and connectors supplier, PEI-Genesis, discusses the special considerations that go into space-worthy cables and connectors
W
ith amazing self-landing rocket boosters, deep-space asteroid hopping probes and the reignition of Moon missions over half a century on — the space race might be over, but the race to exploit the final frontier is just heating up. Down here on Earth, it’s easy to forget how good we have it. Just a mere hundred kilometres up, you’ll find blistering heat, frigid cold and pressures bordering on a vacuum. Even getting equipment out of Earth’s gravity-well and into space is a monumental hurdle — there are reasons why rocket boosters are the size of tower blocks, after all. Any equipment put into space is also completely inaccessible to maintenance, meaning every little detail of design must be considered, with connectors and cabling near the top of the list. Otherwise, if something breaks, disconnects or encounters errors, you’ve effectively just launched a very big, very expensive firework.
Up where there’s no air Every kilogram sent into space costs thousands of dollars, so saving weight is crucial. This can make lightweight plastic connectors quite attractive as they offer higher strengths at lower weights than other materials. However, plastics can encounter problems in the near-vacuum environment of space.
The problem is that many plastics degrade when exposed to vacuum, through a process called outgassing. Here the extremely low external pressure literally boils volatile
30 MAY 2021 | ELECTRONICS TODAY
compounds out of the polymer lattice. This can have a number of negative effects. Firstly, unregulated outgassing like this strips the plastic of some of the particles that help hold it together, causing components to become brittle and directly reducing their expected lifespan. Furthermore, the cloud of loose particles condenses on surfaces inside the space vehicle, such as sensors and other equipment.
Seeing as replacing embrittled connectors and cleaning these laminated sensors would require another multi-million-dollar rocket, avoiding outgassing is crucial. The way around this is to treat the connectors before they’re launched.
At PEI Genesis this is achieved by baking its wide range of space-bound connectors in a vacuum-sealed kiln. This process gradually bleeds the volatiles from the plastic, removing any possibility of further outgassing while also preserving the strength of the material. The connectors are then closely inspected and tested to ensure they meet the stringent requirements of space, aerospace and military applications.
Removing residual magnetism Unfortunately, metallic connectors can bring another problem with them — residual magnetism. This is because the permanent magnetic field affects nearby equipment, degrading performance and potentially ruining data retrieved from them. Examples of equipment sensitive to
magnetism in this way include camera charge-coupled devices (CCDs), onboard vibration sensors and accelerometers, gyroscopic reaction wheels, bimetallic thermometers and, naturally,
magnetometers. Errors introduced into these measurements can turn mission-critical data into meaningless garble, and could potentially cause complete failures if left unchecked.
A mertial matter
Avoiding residual magnetism in connectors comes directly down to the materials used. Wherever possible non-metallic connectors should be used, but metallic connectors constructed specifically with low residual magnetism include the ITT NM/NMB D Sub range. These come in a variety of metallic shell materials, from low-magnetic brass and aluminium, to specially demagnetised stainless steel. They are all tested to ensure they meet space-grade standards. It’s not always true that what goes up must come down, but that’s half the problem if equipment performs badly or breaks while in orbit. Getting up there is a serious task, so making sure only the highest quality connectors reach the launchpad should be top of the list of design and engineering priorities.
PEI-Genesis
www.peigenesis.com
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74
