FEATURE RACKS, CABINETS & ENCLOSURES
Three key considerations when designing an electrical enclosure
Electrical equipment requires robust protection and a durable enclosure is vital to its safety. Here, Andrew Keith, product development director at power resistor manufacturer Cressall Resistors, explores the top considerations when designing an effective enclosure
W
hen designing a complex network of electrical components, an
enclosure may be something of an afterthought. After all, it is simply a box that houses electrical components and connections, wiring, machinery controls and related equipment - all the important stuff. However, it is this misconception that
leads to failure - especially if important design considerations are forgotten or unfulfilled. Although enclosures can seem like a non-critical element in electrical system design, a failure to secure electrical equipment can result in a build up of moisture or dirt, a drastic change in temperature and poor ventilation.
KEEP YOUR COOL When designing a heat management system for an enclosure, manufacturers must account for external temperature fluctuations such as solar gain - heat from the sun. In addition, electrical equipment can generate significant heat as a by-product of their operation, known as losses, inside the cabinet. Failing to safely remove these losses will
14 FEBRUARY 2021 | ELECTRONICS
increase the temperature inside the enclosure and could adversely affect its contents. One remedy is passive cooling. This technique uses the
simple principal of convection to distribute heat from a higher temperature area to a lower one. To do this, enclosures must be designed with strategically placed vents that replace hot air inside the enclosure with cooler, external air. However, the feasibility of passive cooling depends on its
environment and the ambient temperature surrounding the enclosure must remain lower than the air inside it. Additional air filters may also be required to prevent dust or dirt from infiltrating the enclosure. Instead, design engineers may want to opt for active cooling by installing heat exchangers or air conditioners to cool the air inside the enclosure. Of the numerous materials available for electrical
enclosure construction, each offers its own protective benefits. While painted carbon steel is the most cost-effective metallic choice, it has limited resistance to solvents, alkalis and acids and is thus best suited to indoor applications. Stainless steel provides a much higher
resistance and variants such as grade 316 are specified in industries that require resistance to chemical attack, such as pharmaceutical manufacturing, which must avoid excessive metallic contamination. As the material has better resistance against sulphates, seawater and high temperatures, we recommend this type of steel as the preferred choice for both indoor and outdoor applications. Away from metals, fiberglass is a
lighter weight choice, making it suitable for wall or pole-mounted installations. As fiberglass is not conductive, any open circuits would stay safely inside the enclosure and wouldn’t be transmitted through the material. The conductivity offered by a metallic enclosure enables it to be ground connected to reduce the risk of electrical shock should an exposed conductor come into contact with the enclosure. Many manufacturers design and build
enclosures at a central location, such as Cressall’s facility in Leicester, before shipping the equipment to the end user. For an enclosure to comply with local guidelines, manufacturers must consider its end destination. Standards typically referenced are the International Electrotechnical Commission (IEC) 60529 Specification for ingress protection (IP) for countries using IEC standards, while the applicable EN standard should be followed for the European market. Understanding these regulations can
be daunting, which is why manufacturers should work alongside their customers to advise on the most effective solution. If the IP rating is too high, for example, it will place tighter restrictions on the openings in the enclosure panel work and restrict ventilation. Enclosures should only be opened
“Enclosures must be designed with
strategically placed vents that replace hot air inside the enclosure with cooler, external air...”
using a key or tool and when all live parts are disconnected. Installing a viewing window reduces the need to access inside the enclosure. Other safety features include interlocking the enclosure door with a disconnecting device to prevent direct human contact with equipment, should the door need to be opened.
Cressall Resistors
www.cressall.com
/ ELECTRONICS
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46
