search.noResults

search.searching

saml.title
dataCollection.invalidEmail
note.createNoteMessage

search.noResults

search.searching

orderForm.title

orderForm.productCode
orderForm.description
orderForm.quantity
orderForm.itemPrice
orderForm.price
orderForm.totalPrice
orderForm.deliveryDetails.billingAddress
orderForm.deliveryDetails.deliveryAddress
orderForm.noItems



are typically designed for a narrow measuring range, however wide range versions are available. Choosing the sensor to cover just the measuring range required will usually produce the best results. Measuring ranges can be as small as 0.03bar or up to 1000bar.





Measuring the level of solids or liquids in a tank, silo or other container can be divided into Point level and Continuous categories, which subdivide into contact and non-contact. Point level detects when the material has


reached a certain point, and continuous level where the level of the material is measured over a range. The sensor output is either analogue or digital data. Point level is often used for either pump in/out


control or as a call for manual fill. When the low level is detected the pump is turned on to fill the tank, or an alarm is given for the tank to be manually filled by the operator. When the level reaches the high level the pump switches off or the operator is warned that the tank is at the desired level.


Typical sensors for point level are: • Optical, either looking through a sight glass or down on to the material surface. (Non-contact).


• Float switches, which sit on a liquid surface and activate a switch. (Contact). • Capacitive, which detect change between the (non-metallic) tank wall and liquid. (Non-contact).


Continuous level measurement typically uses: • Probes: These work on a principal of conduction, either electrical or microwave. The probe or probes extend into the liquid and the liquid conducts the energy to a second probe or metal tank wall. The amount of conduction increases with the length of probe covered by the liquid. They can be used in pressure tanks but need a liquid with a


dielectric constant greater than 1.8. (Contact).


• Ultrasonic: These work by bouncing a sound wave off of the surface of the medium and measuring the time of flight. They can have either an analogue output or digital data. They require a medium that doesn’t absorb sound. (Non-contact).


• Radar: These work in a similar way to ultrasonic but use pulses in the GHz frequency band. They are accurate and not affected by surface foam, temperature or pressure. Different frequency versions are available to detect different materials. They are often a good substitute for ultrasonic and also have analogue and digital data outputs. (Non-contact). • Optical: Laser point and laser area scanning. Optical sensors and laser point sensors measure the distance to a point or small area on the target material. They have switched, analogue, and digital data outputs. (Non-contact). Area scanning laser sensors measure the


distance to tens of thousands of points in an area and can output the peak height and percentage fill of a container. They are a good choice for containers with an irregular fill level, or containers with randomly sized items.


 Flow sensors are typically contact type sensors: • Mechanical Moving: The fluid either turns a rotor and the rotational speed is used to calculate the flow, or the fluid moves a piston in an internal chamber and the amount of movement is used to calculate the flow.


• Differential Pressure: A flow restriction is used which creates a pressure drop, and the pressure is measured either side of the restriction. The flow rate is calculated in relation to the size of the pressure difference. Not suitable for low flow rates.


• Calorimetric (heat transfer): The flow of the medium over the probe transfers heat from one side to the other. The amount of heat





transferred is proportional to the flow rate. The temperature of the medium is also measured. There are, however, many other types of


flow sensors such as electromagnetic for conductive materials, ultrasonic using the doppler effect, and vortex detection.


 Humidity sensors have to have an open-face construction in order for the moisture in the environment to interact with the sensor. • Capacitive: a hydroscopic dielectric material between two electrodes changes the capacitance as the humidity changes. • Resistive: a polymer material changes its electrical resistance with moisture absorption. Typically less accurate than capacitive. Temperature and humidity sensors are often combined.


 The most common type of vibration sensors use accelerometers in one, two or three planes. They are commonly used for condition monitoring for predictive maintenance. A single plane vibration sensor will detect the vibration in one direction of motion. This may be sufficient if the direction of the expected vibration is known. A worn bearing in a motor will typically produce vibration perpendicular to the rotating shaft. However, a worn thrust bearing creates axial vibration (in line with the shaft) and a two or three axis sensor will be better to detect this. Turck and Banner Engineering combined


are said to have the widest range of sensors in the world so, whatever your sensing needs, a solution will be available.


Level sensing


  


  39


Page 1  |  Page 2  |  Page 3  |  Page 4  |  Page 5  |  Page 6  |  Page 7  |  Page 8  |  Page 9  |  Page 10  |  Page 11  |  Page 12  |  Page 13  |  Page 14  |  Page 15  |  Page 16  |  Page 17  |  Page 18  |  Page 19  |  Page 20  |  Page 21  |  Page 22  |  Page 23  |  Page 24  |  Page 25  |  Page 26  |  Page 27  |  Page 28  |  Page 29  |  Page 30  |  Page 31  |  Page 32  |  Page 33  |  Page 34  |  Page 35  |  Page 36  |  Page 37  |  Page 38  |  Page 39  |  Page 40  |  Page 41  |  Page 42  |  Page 43  |  Page 44  |  Page 45  |  Page 46  |  Page 47  |  Page 48  |  Page 49  |  Page 50  |  Page 51  |  Page 52  |  Page 53  |  Page 54  |  Page 55  |  Page 56  |  Page 57  |  Page 58  |  Page 59  |  Page 60