GUEST COLUMN
Getting a grip Caldwell recently supplied four lifting tongs for a major aluminium plant expansion in the US’s Midwest. The products included a 60,000lbs capacity, two-point swivel tong for ingots 74” to 84” wide; and 50,000lbs capacity, four-point horizontal tong for 54” to 67” wide aluminium ingots.
as whether the product is being picked out of a box or crate; the amount of room available around the part; what the user needs to do with the product after they pick it up; and the obstructions that might be present when they set it back down.
Kent Henry, sales engineer at The Caldwell Group.
Types of tongs
Even within a single manufacturer’s line of lifting tongs, there is often more than one option that could meet the requirements of a material handling application. To begin the selection process, it should be decided whether a single or dual gripping tong is required. A single tong will have one set of arms that, when
lifted, provide a scissoring action to grip a product. A single type of tong only provides one point of contact on the load being picked up, which means the clamp must be centred over the length of the product to keep it level. A dual gripping tong consists of two or more
single tongs suspended along a main lifting beam. The tongs are positioned at a defined distance apart along the beam, which allows the lifting points to be spread out over the length of the load, which will help make it stable. Bale lifting tongs are used to lift square or
rectangular bales of paper, cotton and other materials. A wide gripping surface helps load stability, while an auto-latch mechanism facilitates one-person operation. Dual custom gripping tongs are better suited to handling steel dies, boxes or crates. Contoured pads distribute the force applied to the load over a larger surface area. There are other tongs for lifting round pipe sections, concrete products and structural steel beams. A friction tong applies an inward or outward force with a scissor or lever mechanism to grip a product allowing it to be lifted. An indentation tong will typically have some sort of teeth or points to provide additional support. Lifting tongs are designed to be used with any type of overhead crane or chain hoist. A mobile crane would be most common in the construction industry, while an electric overhead travelling crane might be used above the hook in industrial settings. As with any below-the-hook lifting device,
For safety, lifting tongs must be used exactly as intended, and should not be overloaded. 58 Spring 2026 |
ochmagazine.com
regular inspections are a requirement. Key points would be any damaged, loose, worn or missing components. Maintaining a lifting tong will consist of proper lubrication and general tightening of fasteners. A lifting tong must be used as intended, meaning users must not overload the device, and should always make sure the load is level and stable. Manufacturers provide user manuals to define proper use and care.
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82 |
Page 83 |
Page 84 |
Page 85 |
Page 86 |
Page 87
