CARPET LEISURELY REFURBS
Dual-bond systems, utilising adhesives with different characteristics, allow carpets to be easily lifted along with underlay when they need to be replaced, without damaging the subfloor, while holding floorcoverings firmly in place over the lifetime of an installation. This makes them ideal for use in areas that require regular refurbishment, explains F. Ball.
When installing carpets over large areas, including function rooms, corridors and entertainment areas, flooring contractors should select an adhesive that will develop a strong enough bond to hold floorcoverings securely in place for the lifetime of the floorcovering.
However, floorcoverings installed with such adhesives will require mechanical removal when it comes to refurbishing these areas.
For this reason, products have been developed that allow the creation of a peelable bond which stops carpet or underlay moving laterally when subject to normal foot traffic, holding floorcoverings firmly in place for the installation’s lifetime, while allowing them to be removed and replaced without significant damage to the subfloor.
HOW TO INSTALL
The type of bond achieved when using F. Ball and Co. Ltd.’s Styccobond F40, for example, depends on when the floorcovering is laid into the adhesive. Laying the floorcovering into the wet adhesive gives a permanent bond. However, the water-based adhesive dries to form a transparent, permanently tacky coating, creating a release bond for underlays.
This can form part of a dual-bond system, where flooring contractors install underlay onto the tacky coating before adhering carpet to the underlay using a specialist adhesive for textile floorcoverings, such as F. Ball’s Styccobond F3, which will develop the high bond strength required to withstand expected levels of wear.
PERMANENT BOND
Styccobond F3 is a water-based rubber/resin flooring adhesive that offers excellent wet grab and rapidly builds up a high bond strength. This delivers a flooring installation that won’t ruck, move or lift throughout its working life, making it suitable for areas that are expected to be subject to high foot traffic in hotel and leisure settings.
The adhesive is suitable for installing a wide range of textile floorcoverings, including hessian, felt, secondary latex and rubber foam backed carpets, as well as cork tiles up to 3.2mm thick. It can be applied over Stopgap smoothing compounds, structurally sound, smooth, dry subfloors of concrete and sand/cement screed, plywood, flooring grade chipboard and hardboard. It is also protected against bio-degradation and can withstand wet cleaning, which is essential for maintaining the appearance of carpeted venues.
Both Styccobond F40 and Styccobond F3 are suitable for use over normal underfloor heating systems and are also approved for use in marine flooring installations, making them suitable for use in combination to install carpet on board cruise ships.
38
www.tomorrowscontractfloors.co.uk A PHOTO FINISH
F. Ball’s Styccobond F40 and Styccobond F3 adhesives were used by flooring contractors from Harris & Hiscock Ltd. to install luxury Wilton carpet as part of the refurbishment of the On 5 restaurant at Ascot racecourse.
Situated on the fifth floor of the grandstand, the flagship fine dining restaurant offers private hospitality and spectacular views of the track, a private balcony, roof terrace and bar.
Contractors began by applying F. Ball’s Stopgap 1200 smoothing compound throughout the entire area to create a perfectly smooth surface for floorcoverings. The product is formulated so that it can be applied over old adhesive residues, eliminating the need for mechanical removal and saving time in these situations. It is low-odour, self-smoothing and fast-drying. Applied at a thickness of 2-5mm, it is walk-on hard from 60 minutes after application and dry enough to receive floorcoverings in as little as four hours.
Once the subfloors had been prepared, contractors applied Styccobond F40 to create a release bond for the new carpet installation in the entrance areas. When the adhesive had dried to a tacky coating, they installed a new underlay to protect the carpet and provide added comfort. Styccobond F3 was then used to permanently bond the new carpet to the underlay. Wood floorcoverings were installed in the lounge areas.
Commenting on the project, Steve Hiscock, managing director at Harris & Hiscock Ltd., who supervised the work, said: “Everything went as expected and was completed ahead of Royal Ascot, and the client is made up with the result, so we’re very happy. We do a lot of work at the racetrack, and we have go-to products for these that we know we can rely on to meet high expectations.”
https://f-ball.com/en
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46
