INSTRUMENTATION • ELECTRONICS
THE HOT TOPIC I
Energy process heaters are failing because of different kind of heat, says Johann Lainer
t has generally been assumed in energy process heaters that pins attaching heating elements to the power terminal do not generate heat on their own. Tat is why they are called cold pins. Many engineers believe cold pins actually generate heat creating an environment that is leading to heater failures. When circulation heaters used in
energy processing applications break, the failures predominantly involve the electrical termination in the device and not the heating element. Tey most often happen in the enclosure in the standoff area between the flange and base plate. Circulation heaters for applications such as hydrocarbon refining, power generation and liquified natural gas processing usually consist of many tubular heating elements held in place by a flange creating a chamber where the liquid or gas flows around them. Te heating happens through conduction. On the other side of the flange away
Watlow’s Aspyre range
only close to the flange
moderately increasing chamber in the entire
enclosure. Te models did not take into account heat generated by the connecting pins. For decades, engineers across the
Optimax heat exchanger
from where the heating is intended is the wiring of the heater connecting the power source to the heating elements. Engineers have traditionally calculated some heat leaking from the chamber to this enclosure. Models have predicted heating in this area
industry have relied on modelling to predict the terminal enclosure temperature for these kinds of heaters.
Unfortunately, the modelling was too simple and flawed in that it did not take into account all of the heat generation points in the terminal. While the cold pins are not made of copper wire that would be found in a traditional heating element, if enough current is passed through the metal pin, it in fact becomes a heater. It gets warmer than most engineers anticipated or expected based on the old modelling. “Our new predictive modelling
Latest enclosure design 64
www.engineerlive.com
shows much more of a curve where the temperature peaks in the centre of the enclosure where the cold pins are located,” says Scott Boehmer, a principal engineer with Watlow. “We always assumed the heat in the enclosure was near the flange, but the temperature in the space was significantly higher away from that area because of the resistance with the pins.” As process heaters designs have gone to higher amperage levels, they have gotten physically larger and have more wattage. It has become more important to understand
total heat generated in the “non-heater” part of the assembly. If designers do not correctly predict the heat generation from all the electric components, the end user is going to have problems, regardless of the fluid running through heater. “Te terminal enclosure area is generally
the weakest part of any process heater assembly, and that is true across the industry. But the heater is only as good as the entire system and it will fail because of a loose connection,” Boehmer says. “Tat’s where the problems occur. It may not be immediately but always before the heating elements fail.” Watlow engineers are looking at ways
to improve enclosure designs to reduce temperatures. Another way to improve the lifespan of the termination area is ensure that the proper wiring is used to install the process heaters. Using wiring not rated for the power load of the heater can also be a contributing factor. “Better understanding the temperature in the enclosure is leading us to multiple ways to deal with the issue and improve reliability for process heaters,” Boehmer states. “It is an exciting time to be working in this field and making an impact for our customers.”
Johann Lainer is with Watlow
www.watlow.com
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68
