MATERIALS HANDLING
to explosive dust, flammable gas, vapour or mist in excess of 10% of its lower flammable limit (LFL); atmospheric oxygen concentration below 19.5% or above 23.5%; there is the potential for material to engulf, entrap or asphyxiate an entrant by inwardly converging walls or by a door which slopes downward and tapers to a smaller cross-section; or contains any other recognised serious safety or health hazards.
ENTERING A CONFINED SPACE Working in confined spaces typically requires special personnel training, safety harness and rigging, extensive preparation, and added personnel for a ‘buddy system’. “Systems designed to minimise permit-
required confined spaces can provide a significant return on investment, and the best time to reduce the amount of confined-space entry for component maintenance and replacement is during the specification and design stages of a project,” says Marshall. Many manufacturers offer systems and products that can reduce the need for confined space entry. Examples include: • Modular chute designs with abrasion-resistant liners
• Chutes that hinge open and lay down for liner replacement
• Skirtboards with external liners • Belt cleaners that can be serviced without confined space entry
• Flow aids such as air cannons and vibrators to reduce build-up
• Modular air cleaners for specific locations rather than centralised dust collection
GLOBAL REGULATIONS, STANDARDS AND BEST PRACTICES
Rules regarding confined space entry vary greatly depending on the country, even down to the state, province or prefecture level. As always, regional and local codes should be identified and followed, but general rules can be drawn from regulations established in major industrial markets such as Australia/New Zealand, Canada and the USA. Commonalities between governmental regulations provide employers with a measured approach to safety. Tese procedures include:
Prior to starting the job • Review the permit and the job- specific work procedures
• Gather and inspect all necessary PPE • Test and/or calibrate any safety gear, test instrumentation or communication tools
• If a current Job Safety Analysis (JSA) or safety check list does not exist, perform a risk assessment
• Hold a pre-job meeting making sure all workers are aware of the hazards and safe work practices
• Conduct proper tests for toxins, vapour, dust levels, oxygen levels and material-specific hazards
• Perform as much cleaning and maintenance as possible outside of the vessel
• Post completed confined space entry permit outside of the vessel
• Isolate contaminants and moving parts to prevent the accidental introduction of materials
An estimated 7% of the US fatalities recorded by MSHA between 1995 and 2011 occurred in a confined space
• Proper lock-out/tag-out/block- out/test-out procedures must be completed and documented prior to entry
During procedure • Perform maintenance/cleaning using non-toxic substances such as water and avoid using heat/fire in the confined space. Never use oxygen to purge a confined space, as this can create a fire and explosion hazard
• Provide ventilation if possible • Select personal protective/safety equipment such as safety helmet, gloves, hearing protectors, safety harness and lifeline and breathing apparatus
• Assign a trained observer to monitor the procedure and internal conditions, and provide escape assistance if needed
• Practice fast evacuation of the confined space
Never do this: confined space entry by untrained personnel is a formula for serious injury
44
www.engineerlive.com
CLOSING THOUGHTS: COVERING YOUR ACCESS “Over time, well-designed access improves safety and saves money,” Marshall adds. “Safe access that is carefully located and adequately sized will increase dependability and also reduce the downtime and associated labour required for maintenance.” He advises that companies consider equipment designs that minimise the need for confined space entry, including improved access doors, vibrators, air cannons or silo cleaning services. “Conveyor systems that are properly outfitted with appropriate cleaning and material discharge equipment create a safer workplace, while experiencing longer life and less downtime,” he concludes.”
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68
