RENEWABLE ENERGY
hand, and minimise disruptive factors in operation on the other.
a temperature of about 265°C to be able to circulate, have proven themselves for some time. After the melt has been further heated by the solar heat in the central absorber to about 565°C, the salt first flows into a storage tank where it is kept at a constant temperature. Depending on the system, it can remain there for several hours in order to provide heat or energy at night or during cloud cover. Te plant then pumps the salt to a steam generator where the heat of the salt is used to produce steam from water. During this process,
MOLTEN SALT AS STANDARD ENERGY STORAGE An essential starting point for the efficient and cost-saving use of CSP systems is the heat carrier circulating in the system. In the example of a CSP plant used here, sunlight is concentrated by mirrors onto a central tower, which absorbs the light and thus transfers the heat to a liquid energy source inside the tower. Here, the medium often used is molten salts, which are superior to thermal oil because of their properties: while the oil can be used only up to about 400°C, molten salt is stable up to about 565°C. By this means, steam can be generated at a higher temperature, which has a positive effect on the efficiency of the steam turbine and thus on the energy generated in the power generator. For this reason, chemical compounds such as NaNO3 KNO3
and , which must first be preheated to
An essential starting point for the efficient and cost-saving use of CSP systems is the heat carrier circulating in the system. Here, the medium often used is molten salts, which are superior to thermal oil because of their properties
the salt cools down and is then fed back into the cycle. Te resulting steam in turn operates a steam turbine and an electricity generator, which ultimately generates energy.
FREEZING AND LEAKAGE AS PRIMARY RISKS IN MOLTEN SALT However, in this complex process, which is characterised by very large differences in temperature, difficulties arise that can affect both the efficiency and the condition of the system. As the melt makes its way back to the central tower from the steam generator, there is a risk that the temperature of the salt will fall below a specific limit of about 228°C, and the salt will solidify (known as “freezing”). Tis presents a great risk for the plant, as the salt can clog pipes and consequently shut down the entire process. At the same time, a significant amount of energy is required to reliquefy the solidified salt. Tis results in a poor energy balance and endangers the profitability of the plant. A further risk is that leaks may occur at the valves in the pipes used. Tis in turn reduces the temperature of the melt, and the probability of freezing increases. Te loss of salt also has a negative effect on the efficiency of the plant and may lead to downtime if the valves need to be repaired. Excessive heating of the salt is also critical: if a temperature limit of about 585°C, which varies depending on the molten salt, is exceeded, the salt dissolves and can no longer be used.
TEMPERATURE MANAGEMENT ENSURES STABLE CIRCULATION To counter these problems, the temperature is constantly monitored and regulated by a heating system. Tis requires sensitive temperature sensors, which are installed in the storage tanks as well as in the inlet and outlet tanks of the central tower. For a constant temperature of the melt in the storage tanks, powerful heating elements are also required. Tis task is usually performed by six to eight immersion heating elements, which are mounted in an additional cladding tube, and each has a length of about 5m (16ft). Te materials used in the tanks must also be corrosion resistant and suitable for high temperatures. Te austenitic iron-nickel- chromium alloy Alloy 800 or the special steel SS347H, for example, are suitable for the shells of the heating elements. Tis means that temperatures up to 600°C are no problem, the material is corrosion resistant and stable even at low temperatures. Alternatively, parts exposed to media may also be made of chrome-nickel stainless steel AISI 347H, which also tolerates high temperatures and is resistant to intergranular corrosion. But comprehensive temperature management is required not only in the storage tanks: numerous temperature sensors and controllers must be installed in the absorbing tower also, to ensure a uniform flow of the melt. To ensure that the temperature remains constant there, all lines carrying medium are fitted with high-temperature, tubular heating elements, which are characterized by a particularly short heating time and are themselves heat resistant up to 982°C, thanks to the use of Alloy 800 or special steel SS347H. At the same time, the temperature of the melt can be controlled with the aid of control technology in such a way that no locally limited cold zones occur. As an option, mineral-insulated cables can also be used to heat the lines. Overall, the heat management system ensures that the temperature is monitored without interruption, and thus the molten salt can be used without any costly downtimes or loss of efficiency.
Tim Bruewer is with Watlow.
www.watlow.com
www.engineerlive.com 37 xx
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52
