Feature Pumps A step-by-step guide to choosing a pump
Jeremy Salisbury of Brammer, a supplier of maintenance repair and overhaul (MRO) products and services, examines the key criteria in the selection of centrifugal pumps
entrifugal (dynamic) pumps are used in a range of industrial applications to transfer liquids from one point to another. They do this by converting mechanical energy from a rotating impeller into pressure energy (head) that moves liquid through the pump casing and through the system pipework, valves and process equipment. The head dif- ference between the inlet and the outlet, or total head, produced by the pump, is proportional to the impeller speed and diameter. To obtain a higher head, the rotational speed or the impeller diameter can be increased. In order to operate reliably, with optimal energy use and maximum life span, a pump’s design characteristics must suit the intended service. Therefore, the correct selection of the pump is the first step in guaranteeing efficient and appropriate performance, reliable oper- ation and maximum service life.
C Steps to consider
The primary factors in pump selection include: definition of the technological process outline and main process para- meters, such as flow, pressure and tem- perature; determination of the required pumping services; complete descrip- tion of the fluid to be handled in each pumping operation (type of fluid, tem- perature, density, viscosity, vapour pressure, solids in suspension, toxicity, volatility); general layout of the plant and determination of available space in three dimensions; general arrangement and dimension of the piping according to the recommended velocities for each fluid and type of pipe; determination of
elevation for suction and discharge points of vessels, relative to the centre line of the pump; preliminary calcula- tion of friction losses and plotting of system characteristic curves; definition of the working parameters of the pump, namely capacity, head, suction and dis- charge pressures – taking into account any possibility of variations in pressure or temperature at different pumping conditions; determination of any possi- ble exceptional start, stop or running conditions; determination of available NPSH (Net Positive Suction Head); pre- liminary selection of the pump type, design, position, driver, type of sealing, and cooling of seal and bearings – if required; and establishing the type of drive unit (electric motor, steam tur- bine, etc) and its main operating para- meters. In the case of an electric motor, only high-efficiency motors should be used, and variable speed drives should be considered to control the process.
Guidelines for selection 1. Select the pump based on rated conditions as per the data sheet. 2. Ideally the pump should have a suction specific speed of less than 11,000. 3. The BEP should be between the
Centrifugal pumps are used in more industrial applica- tions than any other kind of pump, pri- marily because they offer low initial and upkeep costs
The correct selec- tion of the pump is integral to optimis- ing performance, operation and product life
örger pumps are helping reduce downtime at Chemwaste, a waste management company, despite being used in a notoriously difficult pump application. The company, which offers total waste management solutions, uses three Maintenance-In-Place Börger pumps to handle highly abrasive waste latex with a high solids content that is just part of its six-stream manifold system. Chemwaste’s site manager, Dave Walton, said: “We’ve worked closely with Börger to develop pumps that would be best able to withstand our very demanding process. Börger’s pressurised pre-chamber system pump has dramatically reduced downtime because our previous pumps became blocked up almost constantly and had to be taken out of service for complete stripping down.” David Brown, Börger UK’s managing director, added: “We knew this application was going to be an extremely tough challenge but by Chemwaste giving us the opportunity to work with them and understand their process, we’re very pleased to have provided pumps that make life easier.” Börger Pumps T: 01902 657076
Pumps make life easier in waste management B
www.boerger-pumps.com Process & Control JULY 2012 Enter 224
rated point and the normal operating point. 4. Remember that hydraulic effi- ciency is high at specific speed 2000 and 3000 and is low if the speed drops below 500. Higher efficiency means less vibration and noise. 5. Do not select a pump with maxi- mum diameter impeller. The pump should be capable of a head increase at rated conditions by installing a larger impeller. 6. The head/capacity characteris- tic-curve should continuously rise to shut-off. 7. Minimum continuous flow should be based on hydraulic stability, not temperature rise. Furthermore, the pump should not be operated below minimum continuous flow rate. 8. Select a driver that allows opera- tion to the end of the curve. 9. For safe operation, NPSHA should exceed NPSHR (net positive suction head required) by more than 1m at the rated condition. As the NPSHR varies, depending on the head and flow, it is safer to select the margin at the end of the curve. 10. Consider how the pump will be driven (with reference to energy effi- ciency). A high-efficiency motor should always be specified, while fitting a VSD may also be advisable. Traditionally, centrifugal pumps have been limited to low-pressure-head applications, but modern pump designs have overcome this problem unless very high pressures are required. In order for a centrifugal pump to run correctly, without wasting energy or sustaining internal damage, it must be specified to meet the intended service requirements.
Brammer
www.brammer.co.uk
Enter 225 23
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36