Act, including any modification to the programme under section 108, and the completion of such programme has been confirmed by the Secretary of State in writing.
5. The provisions of section 72 of the 2009 Act shall apply to this licence except that the
provisions of section 72(7) relating to the transfer of the licence shall only apply to a transfer not falling within article 5 (benefit of the Order).
6. Where the words ‘unless otherwise agreed’ or ‘unless otherwise stated’ appear in the
conditions in Part 2, any such agreement or statement may only be given in relation to immaterial changes where it has been demonstrated to the satisfaction of MMO that the subject matter of the approval or agreement sought is unlikely to give rise to any materially new or materially different environmental effects from those assessed in the environmental statement.
PART 2 Conditions
Design parameters for wind turbines
1.—(1) No wind turbine generator forming part of the authorised scheme shall— (a) exceed a height of 200 metres when measured from LAT to the tip of the vertical blade;
(b) exceed a height of 120 metres to the height of the centreline of the generator shaft forming part of the hub when measured from LAT;
(c) exceed a rotor diameter of 170 metres;
(d) be less than 675 metres from the nearest WTG in either direction perpendicular to the approximate prevailing wind direction (crosswind) or be less than 900 metres from the nearest WTG in either direction which is in line with the approximate prevailing wind direction (downwind);
(e) have a distance of less than 22 metres between the lowest point of the rotating blade of the wind turbine and MHWS;
(f) except with the consent of the Secretary of State, have an electrical output of less than 5MW.
(2) In sub-paragraph (1), references to the location of a wind turbine generator are references to
the centre point of that turbine. 2. No meteorological mast, wind turbine generator or HVAC offshore collector station forming
part of the authorised scheme shall be erected within the areas hatched black on the works plan, whose coordinates are specified below and more particularly shown on the Order limits boundary coordinates plan—
Coordinates for restricted build area Point
i ii
iii iv v
vi vii
viii ix x
Latitude (DMS) 52° 17 29.501 52° 19 32.953 52° 19 47.657 52° 20 36.356 52° 20 18.296 52° 23 17.520 52° 21 52.244 52° 18 15.948 52° 7 15.824 52° 4 49.734
103
Longitude (DMS) 2° 21 18.183 2° 29 16.557 2° 34 8.460 2° 34 8.509 2° 28 48.188 2° 31 41.224 2° 34 8.586 2° 34 8.368 2° 32 52.848 2° 30 59.349
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82 |
Page 83 |
Page 84 |
Page 85 |
Page 86 |
Page 87 |
Page 88 |
Page 89 |
Page 90 |
Page 91 |
Page 92 |
Page 93 |
Page 94 |
Page 95 |
Page 96 |
Page 97 |
Page 98 |
Page 99 |
Page 100 |
Page 101 |
Page 102 |
Page 103 |
Page 104 |
Page 105 |
Page 106 |
Page 107 |
Page 108 |
Page 109 |
Page 110 |
Page 111 |
Page 112 |
Page 113 |
Page 114 |
Page 115 |
Page 116 |
Page 117 |
Page 118 |
Page 119 |
Page 120 |
Page 121 |
Page 122 |
Page 123 |
Page 124 |
Page 125 |
Page 126 |
Page 127 |
Page 128 |
Page 129 |
Page 130 |
Page 131