search.noResults

search.searching

dataCollection.invalidEmail
note.createNoteMessage

search.noResults

search.searching

orderForm.title

orderForm.productCode
orderForm.description
orderForm.quantity
orderForm.itemPrice
orderForm.price
orderForm.totalPrice
orderForm.deliveryDetails.billingAddress
orderForm.deliveryDetails.deliveryAddress
orderForm.noItems
ANALYSIS & OPINION: TEST & MEASUREMENT


THE GOAL IS FOR OPERATORS TO INSTALL, ENSURE ALL IS CORRECT, CHECK THAT FIRE SEALS ARE OPERATIONAL AGAIN AND NEVER REOPEN THEM


technicians install multiple fibres up to the rooſtop, terminating them with connectors in a wall-box to get the building ready for future 5G antenna installations. With this type of installation, MDU installers


face different challenges, so it’s important that installation be done right the first time. Installers need an appointment to go inside each apartment. Returning to fix an issue is bothersome for tenants and results in job completion delays. In addition, many installers do not have


fibre testing expertise. Tey are either juniors, have a different background, or do not have the required tools to verify jobs and produce close-out reports before they leave a unit. From a financial perspective, equipping hundreds


Figure 1: a typical FTTP infrastructure


of technicians with state-of-the art OTDRs is impossible. Either way, most technicians do not have the expertise to use OTDRs correctly and efficiently, and investing in OTDR training might be a complex and hazardous recurring investment in regions experiencing high turnaround in their work force.


Fast deployment schedule Contractors are under huge pressure to deploy fast. Tere is no room for delays or repeat truck rolls and their related additional costs. Again, installation must be perfect the first time. In most cases, since technicians do not test


from inside the unit, cabling is tested from the MTR but with limited visibility. When testing from the basement, either with an OFM or an OTDR, defects between the patch panel and the fibre-end are visible, but not if they are close to link-end or inside the residential unit. If the issue is inside the unit, access may no longer be possible, and a new appointment becomes necessary. Breaks before the optical outlet are also not


visible as they will be displayed at the fibre- end with a few centimetres or metres missing. A proper diagnostic can be difficult to atain. It can also be difficult to determine if the final connector is damaged or not properly spliced or assembled, as this last connector is oſten the problematic one.


Addressing the challenges According to Chad Felardeau , fibre optic splicer and tester at Total Install: ‘When wiremen are actually pulling the cables, if they could verify it’s all correct, it would let a lot less errors on our hands when we are trying to finalise and hook up everything to the outside network .’


An optical fibre multimeter (OFM) can


address those challenges. OFMs verify link health in seconds right aſter installation, inside the residential unit before leaving the job. Equipping technicians with an OFM allows them to validate if the connector in an optical outlet is bad and if a replacement is required; if there are any breaks inside the residential unit or necessity to replace the last section, and if there are any bad splices or faults leſt within the residential unit or the pathway down to the basement or make any repairs while pathways are still open. Technicians need a ‘rubber stamp’ on their


work before they can be paid. Tis verification is usually performed by an expert technician who arrives on-site, shoots an OTDR trace and produces a report. However, OTDRs are suitable for expensive


super-techs who represent only about 10 to 20 per cent of an installer’s crew. By equipping technicians with a simple, easy-to-use, fit-for- purpose tool that verifies and troubleshoots during the installation process, technicians can be proactive and ensure that characterisation will pass the first time. A basic installation model of an OFM can be used to address this situation. With massive fibre deployments, avoiding


downtime for test tool repairs becomes very valuable to maximise return on investment. Improving first-time-right installation to protect project profitability is a great benefit to MDU installers. Deployments are evolving and so must the


testing approach, because the cost of keeping the status quo is simply too high. n


Romain Tursi is product specialist, physical layer at EXFO


www.fibre-systems.com


@fibresystemsmag


Issue 29 n Autumn 2020 n FiBRE SYSTEMS


23


Page 1  |  Page 2  |  Page 3  |  Page 4  |  Page 5  |  Page 6  |  Page 7  |  Page 8  |  Page 9  |  Page 10  |  Page 11  |  Page 12  |  Page 13  |  Page 14  |  Page 15  |  Page 16  |  Page 17  |  Page 18  |  Page 19  |  Page 20  |  Page 21  |  Page 22  |  Page 23  |  Page 24  |  Page 25  |  Page 26  |  Page 27  |  Page 28  |  Page 29  |  Page 30  |  Page 31  |  Page 32  |  Page 33  |  Page 34  |  Page 35  |  Page 36  |  Page 37  |  Page 38  |  Page 39  |  Page 40  |  Page 41  |  Page 42  |  Page 43  |  Page 44  |  Page 45  |  Page 46