Technology
Classically modern
After 20 years as a leading supplier of A-sail and code sail furlers, Karver have finally designed a headsail furler… with some fresh ideas
When Karver announces a new product line, many racing sailors pay close attention. However, the latest launch from this innovative French company (which earned its reputation supplying hardware for Vendée Globe, Mini 6.50, Class40, Ocean 50 and America’s Cup campaigns) is primarily aimed at cruising. ‘We’ve known for a while that
we needed to work on a headsail reefing furler,’ says Karver’s COO, Tanguy de Larminat. ‘When our founder Marin Clausin wanted to go cruising with his family, that was a good opportunity to do it.’ Developing a headsail furler is an
obvious next step, given that A-sail and code sail furlers have been the mainstay of Karver’s product portfolio for the last two decades. And for Clausin, the principal design engineer as well as owner and founder, the KRS range of furlers brings his career around full circle. ‘Marin’s father created Profurl
and he could have taken over that company 20 years ago when his father retired,’ de Larminat explains. ‘But for him it just wasn’t focused enough on racing or maybe it was too old-fashioned so he preferred to go and create Karver.’ Coming back to cruising at the
age of 50, Clausin’s main goal when designing the KRS was not to make it lighter than other furlers on the market; in fact it weighs about the same. Rather, his focus was to make it as robust and reliable as possible. For a piece of hardware that plays such a pivotal role in a boat’s ability to sail efficiently in heavy weather, reliability is the most important
aspect of performance. Ease of operation was important. Designing it with his own family in mind, Clausin was keen to ensure his wife and kids could furl a big genoa from the cockpit. Double bearings in both the swivel and drum reduce friction. ‘We’ve also designed a specific block for the furler because often you have a sharp angle on the furling line,’ de Larminat says. ‘On many boats you have to go up near the bow and haul on the line very close to the furler.’ The drumis a lot wider than their
competitors, to givemoremechanical advantage. A useful side effect of the extra width is that it’s half as tall, and a new way of attaching the bottom end brings it closer to the deck by 5-10cm. ‘You can use a longer link if you need it,’ he says, ‘to provide more clearance for the anchor for example.’ The tack of the sail can be attached with either a lashing, a fabric link or a shackle. The KRS is an eco-conscious
design, using a reduced amount of raw materials and all plastic parts are bio-plastics. ‘I know it won’t save the world,’ de Larminat says, ‘but it’s important to us to do what we can.’ The prototype was fitted to Clausin’s own Beneteau Océanis 473. After a season of intensive use, a further 20 units have been tested on a wide range of boats. At one end of the scale is the Orma 60 trimaran Flo (ex Pierre 1er) which Philippe Poupon raced in last year’s Route du Rhum. The others are regular cruisers like Beneteaus and Dufours, two of which are now cruising the Pacific. It’s too soon to make claims about
Above: the KRS headsail furler from Karver has a double-width drum that gives more mechanical advantage when you haul on the furling line and brings the tack of the sail closer to the deck. The drum can be open or enclosed, and either fully or partially finished in wood veneer
reliability, de Larminat says, but the feedback received thus far is all good. Although it’s designed with ease of retrofitting foremost in mind, builders like JPK, Outremer, Pogo, Moody and Catana will be fitting KRS furlers on new or old boats too. Another key factor is cost. ‘People
assume Karver is more expensive,’ de Larminat says. ‘That was true ten years ago but for a long time we’ve been the same price as others, sometimes lower.’ The price for the KRS is thus on a par with its rivals and features like an elliptical headfoil section, a double luff groove and a black anodised finish – usually optional extras – are included. ‘It’s an all-options furler for the price of a standard one,’ he says. ‘Most brands have racing and cruising versions but it makes no sense for us to do that. What is good for racers is good for cruisers as long as the product stays easy to use. ’ There are a few options for the drum, however. It can be open or enclosed and fully or partially finished in wood veneer. The full range of manual furlers is
now available, for 6m to 25m boats. Electric and hydraulic versions are also in the pipeline: ‘We will try to keep the same size range and we’ll have something to show next year,’ de Larminat says. ‘These will have two aspects, one traditional and one very innovative – it’s not the way electrics and hydraulics are normally used for furling.’
www.karver-systems.com
❑ SEAHORSE 53
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82 |
Page 83 |
Page 84 |
Page 85 |
Page 86 |
Page 87 |
Page 88 |
Page 89 |
Page 90 |
Page 91 |
Page 92 |
Page 93 |
Page 94 |
Page 95 |
Page 96 |
Page 97 |
Page 98 |
Page 99 |
Page 100 |
Page 101 |
Page 102 |
Page 103 |
Page 104 |
Page 105 |
Page 106 |
Page 107 |
Page 108 |
Page 109 |
Page 110 |
Page 111 |
Page 112 |
Page 113 |
Page 114 |
Page 115 |
Page 116 |
Page 117 |
Page 118 |
Page 119 |
Page 120
