MACHINERY
SCANNING FOR
SAFETY S
afety laser scanners are a great option to keep workers out of hazardous areas without using barriers, fencing or caging. At their core is an optical sensor that uses pulsed laser light to scan the surrounding area, prompting a dangerous machine to stop if it detects an intrusion. These versatile systems can effectively improve safety on the factory floor, but to fully reap their benefits, manufacturers must mount and configure them correctly. Here Neil Ballinger, head of EMEA at automation parts supplier EU Automation, offers some tips for correct design and installation.
Safety laser scanners are part of the electro- sensitive protective equipment (ESPE) family. They use time-of-flight technology, meaning that they can calculate the position and distance of an obtrusion — such as a worker’s limb — based on the time it takes for a laser beam to bounce off it and return to the unit. If the distance is shorter than the established threshold, the system will cause the machine to stop.
Safety scanners can be mounted vertically or horizontally, they can cover odd-shaped areas that would be difficult to protect with less flexible solutions, such as light curtains, and can be used for several applications, from cutting tools to autonomous guided vehicles (AGVs). Because of their versatility and unobtrusiveness, they are widely popular in manufacturing. But to
ensure that they fully protect your workforce, there are some simple rules to follow.
DESIGN WITH SAFETY IN MIND
When installing a new machine, safety should be a top priority. It’s important to assess potential hazards and identify adequate risk mitigation strategies before the machine is in place, not after. Incorporating a safety system during the design phase ensures that all dangerous areas are properly safeguarded, and will also represent the most cost-effective solution in the long-run. In the case of laser scanners, if you complete the whole machine set up and think of the scanner as an add-on to incorporate in the final stage, you might end up with many blind spots that will need to be either blocked with a barrier or covered with a second scanner, when one could have been enough.
MOUNT AND CONFIGURE CORRECTLY
If mounted incorrectly, laser scanners might not recognise body parts and expose workers to risks. The scanner should be mounted in such a way that workers’ limbs cannot go undetected, for example because they are under, too far above, or behind the laser beam.
It’s also important to configure the correct 38 NOVEMBER 2020 | FACTORY&HANDLINGSOLUTIONS
resolution based on the height at which the scanner is mounted. For example, if the scanner stands at 300 mm, you can select a resolution of 70 mm and be sure that a leg will be detected. But if the scanner is in a lower position, a lower resolution must be chosen to make sure that a foot or leg cannot slip underneath the laser beam. Another important parameter is the scanner’s multiple sampling. This refers to how many times an obtrusion has to be detected before the machine is shut down. This value is usually X2, but a higher value can be chosen to reduce the chances that insects or production scraps might cause the scanner to stop the machine. However, it’s essential to keep in mind that increasing the multiple sampling adds a delay to the system, so the protective area might need to be bigger to give the scanner enough time to react. To determine the correct size of the protective area, it’s essential to perform a new response time test every time that the multiple sampling value is changed.
Finally, keep in mind that, like all ESPE devices, laser scanners must be regularly inspected and tested by a qualified expert to ensure that components have not deteriorated and that the system can still offer the required level of protection.
EU Automation
www.euautomation.com
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52
