ATEX EQUIPMENT & EXPLOSION SAFETY W
hen an issue arises in a heat transfer system, it should be solved as quickly as possible so that it does not negatively impact safety or production or
result in unnecessary costs. Take this example, during fluid sample
analysis, engineers identify an increase in light ends in the fluid. Light ends boil and ignite at low temperatures, reducing the ignition point (flash point) of the thermal fluid. This increases the risk of fire, putting the workforce and facility at risk. Engineers can remove these light ends from the system, but if they do not deal with the cause of the problem, light ends will continue to be generated.
So, what are light endS? Heat transfer fluids operate at very high temperatures for extended periods of time, so if it is not monitored and managed properly, the fluid will begin to degrade and impact production. When operated at these high temperatures,
fluids begin to degrade as a result of oxidation - chemical reactions in the presence of oxygen. Oxidation produces sticky carbon deposits of sludge, which may be corrosive to a heat transfer system. Fluid also degrades by a process called thermal cracking. During cracking, the bonds between hydrocarbon chains break, producing shorter chained light ends that lower the flash point of the fluid. The higher the operating temperature, the more light ends are generated. The rate at which the light ends are produced is also dependent on the oil type and the operating temperature. Hydrocarbon chains can also recombine to form heavy ends that usually cause fouling of the heat transfer system. Engineers have a duty to manage light ends to
reduce the risk of fire in line with legislation such as the Dangerous Substance and Explosive Atmospheres Regulations (DSEAR) and Explosive Atmospheres Directive (ATEX 137).
Top Tips for flash poinT managemenT
There are many treatments for migraines, from cold compresses and over-the-counter medicine, to Botox. however, if you do not deal with the cause of the migraine, for example stress or dehydration, it will keep coming back. similarly, when operating a heat transfer system, the key to maintenance is dealing with the problem, not the symptoms. here Clive Jones, managing director at thermal oil supplier global heat Transfer, gives his advice on effective flash point management.
18 WinTer 2021 | indusTrial ComplianCe
light endS removal Engineers can temporarily install a light ends removal kit (LERK) to remove volatile light ends. Hot thermal fluid flows through the distillation vessel and the gaseous light ends are collected in the liquid phase of the condenser. The light ends are either drained automatically or manually from the system. The system is not open to atmosphere as a hot expansion tank would be. This protects the oil against oxidation ageing. While removing the light ends will improve
safety and productivity, if engineers do not deal with the cause of the formation of these light ends, the problem will reoccur.
ongoing management Implementing a continuous preventative maintenance programme can help to slow degradation and improve efficiency. Regular fluid sampling and analysis enables engineers to get an accurate representation of the condition of the fluid in the system and anticipate what could happen in the near future. Engineers can then intervene and carry out maintenance tasks before
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48
