Cutting Systems
Finding the perfect cut C
utting solutions around the world have had to change dramatically over the years with the advancement in Knife holder technology, knife metallurgy and geometry which was a must to keep a pace with slitter rewinding equipment becoming faster and materials being slit becoming ever more technical from Simple Paper, Adhesive backed materials, Nonwovens to Battery composites all materials needing the same solution but delivered in varying ways. If the knife, and knife set up is not correct then regardless of how new or even how expensive the Slitting machine is the slit quality will be poor.
In many cases knives and knife sets are not normally given the focus needed within the production environment where the norm is to use traditional tooling but in fact knives have changed so much over the years that very often there are better alternatives to the traditional methods. We often use the analogy that fitting poor quality tooling to a state-of-the-art Slitter is like fitting cheap tyres to an F1 Car, it’s just not logical. Blade management and correct sharpening methods on and off site are critical to slit quality consistency and working with a professional knife partner is critical to support the supply chain and make sure you are always getting the most up to date advice. Swemko established in 1975 working closely with Dienes established in 1913 have a wealth of experience and knowledge in all areas of the cutting process from Crush to Shear cut knives and Slitting systems be it mechanical, pneumatic or even electronic. Blade set up is always a critical factor where setting the knife correctly can resolve slit quality issues, material contamination and reduce reel rejection and result in greater blade life. At Swemko we offer our customers full technical consultation to either advise or confirm that best practises are being followed within blade set up. Blade geometry is another area where slit quality and blade life plays a significant factor meaning that having secondary angles and blades with concave bevels to enhance slit quality are very important to achieve those necessary slit quality results. From blades we move to knife holders and slitting systems. The blade holder and
its ability to replicate the same set up time and time again is once again a critical factor in gaining consistency on the slitting lines. Shaft mounted Shear slitters need the correct level of elasticity from the garter spring to create the correct and even side load pressure whereas pneumatically operated individually set knife holders must make sure that side lay pressure and overlap are followed to the correct parameters to enable that consistent cut.
Dienes have developed their latest knife holder the PSGS-DF LED Holder which allows the operator to set the correct overlap every time regardless of blade diameter using a simple sensor system to find the cutting edge, coupled with the easy set system for finding the bottom knife this holder really sets new standards in blade set up for speed and consistency.
There are several blade material options from 1.5 per cent Chrome being the industry standard to 12 per cent Chrome High Speed steel to the advanced powdered metals ASP and tungsten carbide which all have a place with the production environment. All these materials are designed with an aim in mind, and that is blade longevity, to extend blade life on the slitting machine, to reduce downtime and in turn the amount of regrinds giving greater overall blade life and so on some occasion the most expensive knife works out to be the cheapest.
To sum up blades, Blade holders and the actual Blade set up are all technical tools that
need to be understood and at Swemko we are keen to no longer make it a black art but something all users have a good understanding of and can benefit from.
18
November 2025
www.convertermag.com
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46
