abilities for current research workflows. This is much tougher when dealing with
samples that have complex characteristics, such as multi-layered coatings and fine-grained metallic systems. In such cases, the targeting requirement must be sharper, with minimal artefacts produced. Researchers are now looking toward plasma-based focused ion beam (PFIB) systems that use high-energy ion sources to shorten milling times while still offering controlled machining over larger volumes. These systems assist in preparing large
varieties of sample geometry suited to downstream analysis methods. Large-volume chunks, for instance, can be removed for microCT to allow non-destructive imaging in 3D of internal structures such as crack networks or delamination. The systems also enable thin lamellae to be gently removed from regions of interest and analysed via transmission electron microscopy (TEM) to show nanoscale grain structure, dislocations and precipitates. In one recent example, a 135µm high nickel- based pillar was produced in under eight minutes using the Thermo Scientific Helios 5 Laser PFIB. High-volume milling like this supports iterative design workflows and helps materials researchers keep up with the rapid timelines in modern aerospace development.
aterial innovation is essential in the aerospace industry, where the components used in next-generation
aircraft will need to resist severe thermal, mechanical and environmental conditions. Understanding how materials behave under stress at the microscale and nanoscale is crucial to developing materials that can satisfy these needs. Aircraft designs are shifting towards increased speed, more eco-friendly propulsion technologies and enhanced fuel efficiency. As material characteristics must evolve in tandem, new processing techniques, heat treatments and alloy compositions are being investigated by researchers and aerospace engineers. These changes consequently affect the microstructure of a material, which affects further grain orientation as well as nanoprecipitate distribution. Accelerating the research and development cycle requires an understanding of these changes and how they impact behaviour in the real world.
Materials research has, for decades, relied on
46
two-dimensional imaging techniques such as scanning electron microscopy (SEM) to evaluate alloy structure and composition. Powerful though it is, SEM does not image vital interior details, including where cracks extend beneath the surface within materials, sub-surface porosity and morphology of precipitates that develop during aging or thermal treatment. Volumetric imaging enables deeper insights.
Using focused ion beam milling and high- resolution 3D reconstruction, the internal structure of materials can be imaged. This not only enables a greater global understanding of material behaviour, but also where failure mechanisms and microstructural patterns act directly to affect strength, fatigue resistance and thermal stability. Successful 3D imaging outcomes are
directly contingent on well-prepared samples. In aerospace coatings and alloys, preservation of proper geometry, orientation and structural integrity of prepared specimens is of principal importance. Conventional ion beam milling or traditional mechanical sectioning can be time-consuming with possible lack of accuracy and throughput
Once samples are prepared, advanced imaging techniques can reveal the nanoscale features that govern a material’s performance. For example, scanning transmission electron microscopy (STEM) allows researchers to visualise fine details such as nanoprecipitates and dispersoids that form during different heat or aging treatments. These features are critical to the strength and thermal stability of aerospace alloys. In a recent study of a heat-treated aluminium alloy, STEM imaging revealed the presence and distribution of dispersoids that would be difficult to resolve using standard SEM techniques. By combining this with energy-dispersive X-ray spectroscopy (EDS), researchers could map elemental composition across the sample. Thermo Scientific ChemiPhase software then further enhanced the analysis by automatically identifying distinct chemical phases based on EDS spectral data. In this case, the software confirmed the presence of four different dispersoid phases. This kind of chemical phase mapping
provides a fast and reliable way to understand how alloy treatments influence material structure, supporting decisions on processing conditions and composition in early-stage design. So, by combining high-resolution imaging, quality sample preparation and automated chemical analysis, advanced microscopy solutions are helping aerospace researchers design better materials, faster.
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56
