Test & measurement
POWER METER UNDERPINS VDE SYSTEM FOR ENSURING ACCURACY OF ELECTRIC VEHICLE CHARGING POINTS
W
hen the driver of a conventional internal combustion engine vehicle pulls away from a fuel station, they are unlikely to think twice about
whether the amount of petrol or diesel they’ve been charged for is what has actually ended up in their tank. Over the course of decades, public confidence has been established by robust laws that govern how the flow measurement system in every pump has to be accurately calibrated.
Now that electric vehicles (EVs) are accounting for a rapidly increasing proportion of traffic on European roads, public charging points have to earn the same level of trust. That means creating new calibration systems which ensure a driver can be confident that when they have paid for 50 kWh of electricity, their battery has been topped up with that amount of energy. In Germany, it was natural that manufacturers devel- oping metering products for the EV charging market turned to the non-profit VDE Institute to provide a measurement set-up for calibration that complies with the EU Measuring Instruments Directive. The Institute, which employs more than 500 people at its headquar- ters in Offenbach am Main, is behind the VDE mark that for more than 100 years has been synonymous with the safety and quality of electrical and electronic devices, components and systems. Every year, VDE’s independent test engineers subject more than 100,000 devices to product, quality and safety tests that are recognised in more than 50 countries around the world. Creating a measurement system that complies with the EU Measuring Instruments Directive and Germany’s Measurement and Calibration Act was challenging. The law specifies that meter readings must be accurate to at least three per cent and no higher than the actual amount of energy supplied. This means the room for error in calibration is minus- cule: the accuracy of the power meter used in the test system had to be better than the specification by at least a factor of ten, or ±0.3 per cent. At the heart of VDE’s solution is the WT3000E power meter from Yokogawa Test & Measure- ment, whose accuracy of ±0.04 per cent is almost an order of magnitude better than the minimum specification. Combined with a programmable power supply controlled by Yokogawa’s FG420 function generator, the system provides extremely
46
accurate measurement of voltage, current and total energy.
Other features of the WT3000E include a short interval between stored samples of just 50ms, and easy interfacing to precision current sensors supplied by LEM/SIGNALTEC.
For new designs, Yokogawa offers the WT3000E’s successor product, the WT5000 Precision Power Analyzer, a versatile platform that provides a high level of precision and exceptional performance in the most demanding applications. As well as increased accuracy of ±0.03 per cent it boasts high-speed operation up to 10 MS/s (18 bit) and power measurement bandwidth of 5 MHz. During this project, Yokogawa also supported development of the Raspberry Pi-based control program and measurement data acquisition system which provide an interface to the device under test. This was particularly useful when VDE engineers were
faced by an absence of relevant libraries or drivers. Following accreditation by Germany’s national Physikalisch Technische Bundesanstalt (Federal Phys- ical Technical Institute), the test system is now being used by companies manufacturing energy meters for the country’s rapidly expanding network of public EV charging stations. With 1 million charging points set to be installed across the country by 2030, the VDE seal of approval will play an important part in establishing consumer confidence.
VDE engineer Sven Grünberg, who was part of the team that developed the system, has more than 35 years of experience with different types of test equip- ment. In this case, a need for ultra-high accuracy that made the choice of power meter crucial to the success of the entire project meant that he automati- cally turned to Yokogawa.
“To be honest, there is hardly anything else worth considering,” says Grünberg. “The Yokogawa WT3000E has been used in our calibration departments for years, and measures so precisely that it is also perfectly suited for the charging station test bench.”
Yokogawa Test & Measurement
tmi.yokogawa.com
January 2025 Instrumentation Monthly
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82 |
Page 83 |
Page 84 |
Page 85 |
Page 86 |
Page 87 |
Page 88 |
Page 89 |
Page 90 |
Page 91 |
Page 92 |
Page 93 |
Page 94 |
Page 95 |
Page 96
