blood is cleaned using a dialysis machine with a filter acting as an artificial kidney. In-home care allows for more frequent treatment, improving patient outcomes while reducing the overall cost of therapy. In the medical device market, this trend has been a double-edged sword. On one hand, it has increased the demand for certain medical devices. On the other, it has led to greater scrutiny of devices and increasingly stringent safety standards. Measures used to increase safety precautions are often at odds with the need to make home care devices smaller and more portable than those used in a clinical setting. While at home medical devices are improving
A
comfort and convenience for patients, a number of regulations arise regarding safety. Specifically, IEC 60601-1-11 outlines safety requirements for medical devices intended for use in home care settings. Manufacturers must identify the specific product safety risks associated with using their equipment in a non-clinical environment. To achieve certification, manufacturers must mitigate those risks through appropriate product design, in addition to clear user instructions and training.
SAFETY, SIZE AND PORTABILITY An important consideration for any automated medical device is electrical safety. In the design of these machines, some features are considered MOPs (Means of Protection). Medical devices need two or moreMOPs to reduce the risk of electrocution. Traditionally, MOPs have been added to devices with a trained third-party operator in mind (usually in an in-patient setting), in addition to MOPPs (Means of Patient Protection). A clinical setting allows MOPPs that are not
usually present in a home setting, since the patient is now also the operator. Manufacturers must include those MOPPs in the medical device itself, which creates some additional design challenges. In a home care setting, higher levels of patient safety are required than in a clinical setting. This is largely down to the absence of device
training and the risks surrounding voltage and outlets. In a hospital, the electrical outlets are guaranteed to have appropriate voltage, be effectively grounded and tested and certified as
ccording to the National Kidney Federation, around 30,000 people are on hemodialysis in the UK. Hemodialysis is the procedure where
When a home medical device manufacturer approached Watlow for a thermal solution for its home hemodialysis device, Watlow delivered an innovative solution that not only met requirements for size and safety, but also improved the overall system.
Welcometothe May issue of Instrumentation Monthly. The nominations
are in for the 2023 Instrumentation Excellence Awards. The event of the year will take place at the Grand Connaught Rooms in London in October. Visit
www.instrumentationawards.co.uk for more information. Alternatively, turn to page 12 to learn about this year’s event.
safe. But these guarantees cannot be made for a patient’s home. As a result, MOPPs must provide much more protection, as the safety requirements for home care devices will be that much more stringent, and the clinical assumptions about operator health and training cannot be assured. In this case, responsibility for ensuring safe operation shifts to the device manufacturer.
THERMAL SYSTEM CONSIDERATIONS Home hemodialysis machines include a final challenge - fluids must be kept at body temperature to prevent thermal shock. Higher temperatures are also needed to disinfect the machine itself. Unsurprisingly, the heating requirements of these medical devices greatly influence both the size and the electrical requirements of the machine. Heating fluid on demand requires a fair amount of power,
increasing the possibility of current leakage, and the risk to patients. Mitigating those risks is possible with more traditional technology, but that technology adds to both the bulk and cost of medical devices. This is where innovation in thermal solutions, including heaters, sensors, temperature controllers, power controllers and supporting software working together as an integrated system, can make a difference. Watlow’s engineers used knowledge of the full system standards and system level requirements to help the customer create an optimized system architecture for its home hemodialysis device. This featured a FLUENT in-line heater with a ceramic substrate tube and polymer fittings to create an entirely non-metal surface. The FLUENT heater addresses efficiency and electrical safety concerns with a size and weight footprint that is smaller than legacy solutions. In addition, using thermal spray, the heater makes use of its entire surface to produce heat, which optimizes heat transfer and temperature uniformity. The goal ofWatlow’s customer was to design a
home hemodialysis device that met all safety guidelines while being portable and convenient for patient use. Using a systems approach helped Watlow to navigate the engineering tradeoffs between size and safety without compromise, to produce a safe device with a small footprint.
Measuring gases. Focusing light.
www.axetris.com
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82
