search.noResults

search.searching

saml.title
dataCollection.invalidEmail
note.createNoteMessage

search.noResults

search.searching

orderForm.title

orderForm.productCode
orderForm.description
orderForm.quantity
orderForm.itemPrice
orderForm.price
orderForm.totalPrice
orderForm.deliveryDetails.billingAddress
orderForm.deliveryDetails.deliveryAddress
orderForm.noItems
Continued from page 20


At some point in time every MWF reaches the end of its optimum working life and its stability dictates that it is at the point where it has to be replaced.


At this time there is an opportunity to make sure that any useful oil can be recovered and used again. This makes both good economic and environmental sense.


Using metal salts it is possible to reduce the efficiency of the surfactants, to the point where the emulsion will completely split, thus releasing the valuable oil, and allowing it to rise to the surface where it can be collected ready for cleaning and recycling. In the same way that the Turbiscan can be used to determine creaming stability during the working life of the MWF it can also be used at the next stage of the cycle. Optimising the amount of metal salts needed to split the MWF quickly and efficiently.


Access to this level of information allows MWF formulators, users and recyclers alike to all benefit from a better understanding of the MWF material properties as they change over time.


LINK www.fullbrooksystems.co.uk


The Hugo Cartridge™ System


uSWEDISH QUALITY PRODUCTS The Hugo Cartridge is a specially developed packaging for grease. It is manufactured in a standard size for 400 g grease guns but can also be used in some 500 g grease guns. Our cartridges and caps are 100 % recyclable.


uSAFE AND SIMPLE HANDLING The injection-moulded cartridge guarantees consistent quality and high stability. The bottom has an inner seal that locks with the pull cap and the outer edge prevents the cartridge from slipping. The leak-proof pull cap secures the content during fi lling, transport


and storage. The cartridge can be fi lled with hot grease, up to 70 °C. The pull cap is easily removed using the pull ring. The cartridge can also be resealed by replacing the pull cap. Seals at both ends guarantee a fully sealed, leak-proof operation. For lubrication of open surfaces,


The Hugo Cartridge is used with a Hugo Grease Applicator.


uPRINTING UP TO SIX COLOURS The Hugo Cartridge has a very smooth surface that is ideal for advanced screen printing. Designs of your choice can be printed with up to six colours.


ON THE MARKET SINCE 1992 GR PRODUKTER AB, UBBARP, SE–560 30 TENHULT | T +46 (0)36 920 40 | F +46 (0)36 925 82 | GR@GRPRODUKTER.SE | WWW.HUGOCARTRIDGE.COM


Page 1  |  Page 2  |  Page 3  |  Page 4  |  Page 5  |  Page 6  |  Page 7  |  Page 8  |  Page 9  |  Page 10  |  Page 11  |  Page 12  |  Page 13  |  Page 14  |  Page 15  |  Page 16  |  Page 17  |  Page 18  |  Page 19  |  Page 20  |  Page 21  |  Page 22  |  Page 23  |  Page 24  |  Page 25  |  Page 26  |  Page 27  |  Page 28  |  Page 29  |  Page 30  |  Page 31  |  Page 32  |  Page 33  |  Page 34  |  Page 35  |  Page 36  |  Page 37  |  Page 38  |  Page 39  |  Page 40  |  Page 41  |  Page 42  |  Page 43  |  Page 44  |  Page 45  |  Page 46  |  Page 47  |  Page 48  |  Page 49  |  Page 50  |  Page 51  |  Page 52  |  Page 53  |  Page 54  |  Page 55  |  Page 56