search.noResults

search.searching

saml.title
dataCollection.invalidEmail
note.createNoteMessage

search.noResults

search.searching

orderForm.title

orderForm.productCode
orderForm.description
orderForm.quantity
orderForm.itemPrice
orderForm.price
orderForm.totalPrice
orderForm.deliveryDetails.billingAddress
orderForm.deliveryDetails.deliveryAddress
orderForm.noItems
OFFICE & WORKPLACE


floorcoverings from just 20 minutes after application, and priming is not required prior to use, making it ideal for use when working to tight time constraints and deadlines.


PRIMING – PRIOR TO APPLYING A SMOOTHING COMPOUND


Traditionally, it is almost always essential to prime subfloors at this stage. Priming promotes the application characteristics of subsequently applied smoothing compounds and adhesives, particularly when used over absorbent subfloors, such as plywood, as well as preventing smoothing compounds from drying too rapidly, resulting in a reduced working time. It also helps to prevent pin-holing, caused by tiny bubbles resulting from the slow escape of air from the subfloor, which burst on reaching the surface, leaving small pinholes or craters as the smoothing compound dries.


For when working over metal raised access panels, cement- based primers, including F. Ball’s Stopgap Fill and Prime, are available that fill the gaps between flooring panels whilst priming the subfloor, saving valuable time. They have a thixotropic consistency, meaning that they flow freely when stirred but set to a gel-like consistency on standing, enabling the joints to remain filled. They are also suitable for use over well-bonded, waterproof adhesive residues, prior to the application of the recommended smoothing compound.


FIBRE-FILLED SMOOTHING COMPOUNDS


Where the base has been suitably primed and gaps between raised access panels have been filled, contractors should proceed to apply a fibre-filled smoothing compound, such as F. Ball’s Stopgap 700, to create a perfectly smooth base for floorcoverings.


The product is reinforced with tiny fibres that maintain the integrity of the smoothing compound, preventing cracks from forming as a result of minor subfloor movement caused by foot traffic or temperature fluctuations. It is suitable for application over plywood and steel subfloors, including raised access panels, as well as concrete and sand/cement screeds.


Stopgap 700 is also fast setting. It is walk on hard just 60 minutes after application and allows floorcoverings to be installed in as little as three hours, while maintaining a working time of 20–30 minutes, making it ideal for projects where time is tight and reducing the time that areas are out of use. Its protein-free formulation makes it suitable for use in biologically sensitive areas, such as laboratories and hospitals, and it is approved for marine use.


FINAL THOUGHTS


The development of high-performance floor finishing compounds has equipped installers with an ideal solution when time or floor height are critical. Installers need to make the right choice, between using a fibre-filled smoothing compound or a finishing compound that will remove minor surface defects and create a perfectly smooth surface for floorcoverings, without the need to prime, when working over plywood and hardboard.


Following the steps outlined here will ensure the integrity and appearance of a flooring installation for many years to come, avoiding costly remedial work and saving valuable time and money.


https://f-ball.com/en


x.com/TContractFloors


23


Page 1  |  Page 2  |  Page 3  |  Page 4  |  Page 5  |  Page 6  |  Page 7  |  Page 8  |  Page 9  |  Page 10  |  Page 11  |  Page 12  |  Page 13  |  Page 14  |  Page 15  |  Page 16  |  Page 17  |  Page 18  |  Page 19  |  Page 20  |  Page 21  |  Page 22  |  Page 23  |  Page 24  |  Page 25  |  Page 26  |  Page 27  |  Page 28  |  Page 29  |  Page 30  |  Page 31  |  Page 32  |  Page 33  |  Page 34  |  Page 35  |  Page 36  |  Page 37  |  Page 38  |  Page 39  |  Page 40  |  Page 41  |  Page 42  |  Page 43  |  Page 44  |  Page 45  |  Page 46  |  Page 47  |  Page 48