ENTRANCES & FRONT OF HOUSE HEAVY-DUTY
Flooring in entrances is often exposed to moisture and dirt that has been brought in from the outside, as well as having to cope with high levels of foot traffic and extreme temperatures. It is therefore important to select suitably heavy-duty subfloor preparation products and flooring adhesives when installing floorcoverings in these areas, explains F. Ball.
Before proceeding with any flooring installation, contractors should take the time to thoroughly assess the composition and condition of the subfloor to ensure a suitably sound, smooth and dry base for the receipt of new floorcoverings. A smoothing compound can then be applied to create a perfectly smooth base for the receipt of floorcoverings, remembering to prime the subfloor before-hand.
RIGHT FROM THE OFF
When installing floorcoverings in interior entranceways, the application of a heavy-duty smoothing compound is recommended to withstand expected levels of foot traffic and heavy loads.
Heavy-duty smoothing compounds are formulated to have the high compressive strength required to maintain their integrity throughout the lifetime of a flooring installation, even when subjected to heavy daily usage.
For areas that are likely to be subject to rain or frost, such as transitional areas, doorways and walk-ways, an exterior smoothing compound, such as F. Ball and Co. Ltd.’s Stopgap 850, should be selected.
As usual, it’s essential to prime the subfloor before the application of a smoothing compound. Priming external absorbent subfloors helps to promote adhesion, reduces pinholing and prevents the un-acceptably rapid drying of subsequently applied levelling compounds
ENTRANCE ADHESIVES
Once the smoothing compound is fully cured, contractors can proceed straight to installing floorcoverings. Again, it is important to select an adhesive with suitable properties to be able with withstand the elements and pressures put upon it in transitional areas or outside.
Epoxy or polyurethane-based adhesives are the traditional choice for installing floorcoverings in areas that will be exposed to high foot traffic as well as surface water, including external settings. Once cured, they are resistant to water, oil and grease.
30
www.tomorrowscontractfloors.co.uk
The latest advancements in adhesive technology have enabled the development of one-part adhesives for internal and external heavy-duty applications, such as F. Ball and Co. Ltd.’s Styccobond F73 PLUS. The solvent-free, moisture-curing adhesive provides the high bond strength required to firmly hold in place a wide range of textile and resilient floorcoverings, including rubber, vinyl, linoleum and synthetic grass, in areas that will be subject to heavy loads and high foot traffic, as well as surface water.
Styccobond F73 PLUS is also easier to apply and faster curing than traditional alternatives, requiring as little as 90 minutes to secure floorcoverings. Its fast setting properties allow welding of sheet floorcoverings to take place in as little as two hours.
COMPATIBILITY CHECK
As always, it’s recommended that contractors check the compatibility of particular floorcoverings and adhesives. For these purposes, F. Ball produces its industry-leading recommended adhesives guide (RAG), which lists adhesives recommended for use with over 6,000 floorcoverings, produced by over 200 floorcovering manufacturers. It is available on the F. Ball website and as a free app, as well as a printed booklet. Contractors can also consult floorcovering manufacturers for advice.
https://f-ball.com/en
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42
