OPERATIONS & MAINTENANCE
SECTION TITLE
to change an element 3,000m below the surface. Terefore, the integrity of the filters is particularly critical in these types of environments.” Barnett adds that when repair or replacement is necessary, having a filter supplier with global presence able to offer speedy supply of spare and replacement parts is very important to keep things operational and productive. Te supplier should also be able to provide bespoke filters when required and be able to offer a comprehensive range together with full documentation.
MONITORING Wright makes the point that equipment monitoring is also important. “Because most of the subsea market is moving to water glycol systems, monitoring their fluid cleanliness becomes more difficult using the laser technology that is common across the industry. In this regard, a key differentiator for Pall is the use of its PCM500 series fluid cleanliness monitor. Te monitor uses a mesh blockage technology that is not affected by the presence of water, so it provides consistently accurate and reliable fluid cleanliness measurements.” Also, with big data and the growing use of cloud-based solutions, Webb explains that remote and on-site monitoring can be undertaken, bringing additional benefits of convenience and cost savings. “Te use of data and data analytics will continue to be a key industry focus with regard to cleanliness monitoring,” he says. “Pall and other filtration companies see the importance of making it easier for equipment users to both maintain the filter element and monitor the service fluids that pass through them as effectively as possible. Tey’ll do this by offering effective monitoring solutions that are able to harness the benefits of machine learning and the Internet of Tings.”
EDUCATION According to Geoff Grant at MP Filtri, the main challenge for particle counters and condition
monitoring equipment within the onshore and offshore oil and gas sector is education. “It is important to understand the reasons why all fluids and operating systems have to be cleaned to suitable levels. Tis is to prevent damage to hydraulic components and contamination of tooling and equipment when connecting them to topside and subsea,” he says. So, what are some of the key functionality must-haves to look for in particle counters to best ensure maximum efficiency and reading accuracy? “Be aware of the fluids you are analysing and use the correct type of particle counter suitable for those fluids, seal material and wetted parts compatibility (i.e. synthetic, water or mineral oil-based),” says Grant. “Also, be vigilant not to cross-contaminate these fluids.” He adds that it is also important to
Pall’s PCM500 product
barrel in 2016 Hydac was asked to reduce price of its filters by 20%. “To achieve this, we designed a budget filter where features were removed and changes in the grade of stainless steel which is a little cheaper but still highly anticorrosive,” he said. “Tus, we created
a larger range, one with all the features such as bowl drain and one known as a budgetary filter housing to give a price saving.”
ensure they are flushed and cleaned with the appropriate fluid so as not to affect the readings of the particle counter or monitor they are using. Grant also stresses that users should know and use the correct international standards appropriate to today’s technology and equipment. “Most standards were written many years ago and I feel the levels of cleanliness required today for the majority hydraulic components and systems are not stringent enough,” he remarks, adding that the market has seen an increase in component sensitivity, operating at higher pressures and faster speeds.
Effective filtration is non-negotiable
MEETING DIFFERENT CHALLENGES Because of the variations among oil wells and what they produce, each well poses different challenges. For instance, Wright explains that if chemicals are put into the water stream they could cause polymerisation and blocks filters. “In the case of condensate filtration and dewatering, waxes may be present. Tis makes accurate sizing critical to ensure you are not sizing the filtration system based purely on hydraulic flow rate.” Barnett points out that there might also be financial constraints at play. When the oil price dropped below US$50 per
SATISFYING REGULATORY REQUIREMENTS Safety compliance is also a non-negotiable when it comes to oil and gas applications. As Barnett explains, previously just ATEX was asked for. Tis then progressed to IECEX and then North American standard UL. “Hydac therefore supplies an electrical clogging indicator suitable for hazardous areas that has triple approval,” he says. “Tere is a lot of work taking place in the background that customers do not see, such as the design and updating of technical files to comply to updated standards and regulations, along with quality assurance. We pressure-test every stainless-steel filter that leaves our production facilities. 100% have to be good; we cannot afford a defective filter reaching a customer – especially when it comes to subsea applications.”
MAINTENANCE And what of ongoing service and support for filtration solutions in the oil and gas sector? Webb points out that demand is high for greater ease of service and filter products’ maintenance. “For example, Pall’s hydraulic and lube oil filters now feature a top service cap that can simply be unscrewed to ease service, rather than having to remove the complete element bowl. Users also benefit on space because this design can be put in situ in an environment that is easier to handle and safer for operators to maintain, therefore reducing the risk of workplace injury.” So, for a wide range of applications within the particularly challenging oil and gas sector, effective filtration systems are a non-negotiable.
Visit the British Fluid Power Association website at
www.bfpa.co.uk
www.engineerlive.com 25
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60
