PRODUCTION • PROCESSING • HANDLING
DRYING GAS UNDER WATER
Pump manufacturer ensures safe glycol injection for natural gas production off the coast of Mozambique
into account, and the quality of the extracted raw material must be ensured. Tis can be impaired by underground salt domes in caverns, which can cause the extracted gas to have an increased degree of humidity, in turn hindering later compression. Te moisture must be removed by injecting glycol and thus drying the gas. Tis is necessary in a French mineral oil group’s current project. After acquiring production rights off the north coast of Mozambique, the group has begun preparations for extensive LNG production. Since the offshore units through which the natural gas is produced are not located on a platform but underwater, the glycol is pumped from the coast via pipelines directly to the production sites. Lewa Nikkiso America was commissioned to provide the pumps required for this purpose. It is a subsidiary of German firm Lewa, which is known for its expertise in this field. For the time being, two of a total of seven planned production branches were to be equipped with process diaphragm pumps. “Te biggest challenge in this project
W
is certainly the combination of high back pressure from the production site and the large amount of monoethylene glycol required, which has to be conveyed to the well around the clock. Te MEG must be injected continuously despite this
hen natural gas is extracted at sea, adverse weather conditions, rough seas and high pressure under water must be taken
A total of three pumps will be installed per production branch, with one pump being kept available as a stand-by unit. This results in an output of about 36m3
/h
pressure,” says Holger Henze at Lewa, which is responsible for manufacturing the pumps at the company’s headquarters in Leonberg, Germany. “At the same time, we have to ensure that the pumps are 100% reliable so that even maintenance does not lead to an interruption in the gas drying process and thus to a costly delay of the entire pumping process. Last but not least, the aggregates should function as economically as possible.”
IMPRESSIVE FLOW RATE To counter these problems, the team from Lewa decided to use the proven triplex pump with pump heads specially designed for this application. “Te G3U variant in combination with the M800 pump head enables a flow rate of 18m3
/h per pump,
The pump heads are special models that can also work with a PTFE sandwich diaphragm, thanks to a diaphragm clamping system that has been designed for high pressures
32
www.engineerlive.com
despite the high back pressure of 517 barg,” explains Henze. A total of three pumps will be installed per production branch, with one pump being kept available as a stand-by unit. On the one hand, this results in a flow rate of about 36m3
/h MEG and on the other hand, the
reserve pump can step in if maintenance work has to be carried out on one of the
other pumps. Reliable, constant injection is thus ensured, and interruption of natural gas production is largely excluded. “Te pump heads are special models that can also work with a PTFE sandwich diaphragm, thanks to a diaphragm clamping system designed for high pressures,” says Henze. “Comparable pumps must otherwise be equipped with a metal diaphragm to withstand the high pressure. However, for design reasons, such diaphragms are hardly feasible in the size for the drive unit used in this power class.” At the same time, the pump head takes up less space and is more compact than models with the stiffer metal diaphragm, which would require a much larger diaphragm diameter for the same degree of displacement. Tis would automatically lead to a larger pump head diameter. To reduce pulsations and avoid vibration-induced damage, resonators are also used to ensure that the medium flows evenly. Like the base plates, they are manufactured at the Lewa Nikkiso Middle East plant in Sharjah (United Arab Emirates). Te final assembly, including the piping, will take place in Leonberg.
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52
