COATING TECHNOLOGY
accelerate the development of tomorrow’s passenger and commercial vehicles.
BATTERY PACK CHALLENGES EV battery packs present some familiar challenges addressed by the automotive industry with coatings and surface solutions: pack components must be protected against corrosion and impact, bonded, and sealed from outside elements. Electrodeposition and powder coatings, adhesives, and sealants address these needs, extending service life. Te battery pack, including the battery management system (BMS) – the electronic “brain” of the system – must be protected from electromagnetic interference (EMI) or “crosstalk” with other safety and performance-critical electronics in the vehicle. Tis is accomplished with EMI shielding, including using thin conductive coatings that conform to the electronics enclosures. EV battery packs also present new, unfamiliar challenges for the automotive industry. Specifically, dielectric isolation, thermal management, and fire protection are essential for safety, performance and lifetime. EV batteries operate at high voltages, and components must be electrically isolated. Battery cells have a narrow thermal operating window that must be tightly maintained. Control system malfunctions, manufacturing defects, overheating or heat exposure, or damage from collision can result in thermal runaway events with intense and energetic fires.
Tese challenges are heightened by the race to push the performance limits of the battery packs. Increasing EV range per charge and decreasing charging time are key to overcoming barriers to adoption. Tis has led to higher operating voltages, the development of higher energy battery active materials with increasing temperature sensitivity, and higher-capacity cell and pack formats. As EV designers and manufacturers work to decrease charging times, waste heat fluxes during charging will be higher. A battery is most likely to experience a hazardous malfunction when it is at a high state of charge and when it is overheated. Te importance of effective dielectric isolation, thermal management and fire protection is growing with current battery design trends.
OVERCOMING THE CHALLENGES Tese most critical new industry
The internal workings of a typical BEV
Dielectric isolation, thermal management and fire protection are essential for EV safety and performance
challenges can be effectively addressed with advanced coatings and surface solutions. Coatings can be designed to be multifunctional, addressing several challenges simultaneously, while reducing manufacturing complexity, weight and cost. Dielectric isolation coatings can provide
corrosion protection while enhancing thermal management and enabling enhanced bonding. Corrosion coatings, adhesives and sealants can include fire mitigation functionality. Fire mitigation coating systems can include shielding to address EMI of configured to provide dielectric isolation. Tese multifunctional coatings are conformal and can be applied seamlessly to complex three-dimensional shapes and adapted quickly to different platforms or changing designs. Lastly, battery EVs must be manufactured on an assembly line to maximise output. Coatings have been applied in an assembly line process for decades and provide reliable, high-volume, automated production of battery cells, modules and packs which reduce operating costs by increasing manufacturing output.
STANDARDS AND TESTING As the number of EVs continues to increase, globally harmonised manufacturing standards and unified testing protocols must be developed to minimise risks associated with the high amount of energy on board. Currently, EV manufacturers are at very different maturity levels regarding standards, critical requirements, and specification and test capability against which to measure safety solutions.
Coatings providers with an advanced understanding of industry standards and the capability to test and qualify materials can facilitate and accelerate identification and approval of protective materials. Te evolving EV market will favour the simplest and lowest total cost option and manufacturers and consumers will both benefit from clearly defined safety requirements.
Calum Munro is a Senior Scientist, Mobility at PPG.
www.ppg.com
www.engineerlive.com 27
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44
