74
PROJECT MAKING ACCESSORIES Preserve your mandrel with the
The Mandrel Saver Live Tailstock Center See page 12 for more information
“Super Drive” Revolving Tailstock Center
This multi-tooth live tailstock center provides a great grip
A LCENTTS2 #2MT 3/4"
dia.Super Tailstock Center ..................$
Live Tailstock Center Large & heavy duty with 60" point and ball bearing precision B LCENTLT1 #1MT 1-1/4" dia. Live Tailstock Center ..................$ LCENTLT2 #2MT 1-11/16" dia. Live Tailstock Center .............. $
Mini 4-Prong Drive Centers Ideal for turning spindles
With a diameter of only 3/8" these centers are ideal for turning smaller radius spindles. They also provide easier access to the ends of larger diameter spindles. Polished and hardened steel.
LCENTMDC2 #2MT Mini Drive Center ............................................$ Super 4-Prong Center
Gives a strong bite into wood. Features a spring-loaded center point that simplifies positioning your spindle and retracts to avoid splitting work when tailstock pressure is applied. #2MT - 1" dia ............................................................$
LCENT3210
Morse Taper for Lathe Headstocks or Tailstocks
Used for grabbing small turnings or pen mandrels on the headstock - or a drill bit in the tailstock.
Accepts a 1/4" x 20 draw bolt. C TM-31
C TM-21 C TM-32
19.95
Double-faced Mounting Tape Mount blanks to face plates Strong bond. 3/4" width x 108 ft mounting tape CMTAPE Mounting Tape ............................$
13.95
Super Powerful Rare-Earth Magnets
#1 Morse Taper, 1/2" Chuck (Carba-Tec, TCLPLUS, PENPAL) ....$ #1 Morse Taper, 3/8" Chuck (Carba-Tec, TCLPLUS, PENPAL) ....$ #2 Morse Taper, 1/2" Chuck (Delta, Jet, TCLPRO) ..................$
D TM-32KL #2 Morse Taper, 1/2" Chuck (Delta, Jet, TCLPRO) ................$
14.95 14.95 29.95 34.95
Set of 2 Vertical Pen Blank Drilling Jaws
Use these aluminum utility jaws to convert your drill press vise into a great new pen accessory
The jaws includes grooves cut vertically to support your pen blank for drilling.Horizintal grooves allow you to postion a turned barrel or plain brass tube horizontally for cutting or
squaring.The jaws easily drop onto your drill press vise and attach magnetically (to jaws over 1in. high).Great for other gripping and positioning applications.
PKVJAWS2 Vertical Jaws ............19.95/set
Vise not included
Jaws install instantly onto any vise
Lifting capacity is 2-1/2 lbs for the 1/4" magnet up to 30 lbs for the 1" magnet.
You’ll find a multitude of uses for these powerful “Rare-Earth Magnets.”Make jigs, fixtures, clamps, tool holders or the best fridge magnet in the world.
SIZE QTY/PACK PRICE
EMAG14 ....1/4" dia x 1/10"....20 ......$ EMAG38 ....3/8" dia x 1/10"....10 ......$ EMAG12 ....1/2" dia x 1/8"......10 ....$
Mini Brass Barrel Hinges Ideal for small boxes Simply drill a 5mm hole to accept the
hinge.The installed hinge operates smoothly. Sold in packs of 10. BHINGE
Hinges......................1-9 Packs $ 5.10 pk 10+ Packs $4.60 pk TO ORDER • Call: 1-800-858-9295 • Fax with PO: 215-676-3716 • E-Mail with PO:
maria.schools@
pennstateind.com
9.95/pack 4.95/pack 12.95/pack
14.95
4 Piece Drive Center Set for #1 MT and
#2 MT Lathes Includes hard to find replacement centers
Avoids splitting your wood. It has sealed bearings and spring loaded point for easy positioning and wood removal.
42.95
19.95 15.95
Live 1/2" Tailstock Drill Chuck Precision centering
Get precision centering and griping of your work at the tailstock end of your lathe. Ideal for holding mandrels,dowels and tenons up to 1/2" dia. Features smooth precision ball bearing operation.
Available for tailstocks that accept either #1 or #2 Morse Taper adapters. NOT FOR DRILLING LDC2MT #2 MT Live Drill Chuck........................................................$
The PSI Super Centers Get a better bite on your spindle
A spring-loaded point simplifies the positioning of your spindle in the center and retracts to avoid splitting your work when tailstock pressure is applied.
E LCENTSS21 #2MT 5/8" Crown..............................................$ LCENTSS22 #2MT 1" Crown..............................................$
22.95 22.95
39.95
For lathes equipped with #1MT or #2MT headstock and tailstock centers. Packaged in convenient wood box. Includes: 5/8"dia. headstock spur center for narrow spindles • 1"dia. headstock spur center for standard spindles • Live ball bearing tailstock center with cup and point • Hollow center for drilling 5/16" (#2MT) through holes (for lamps, etc) and 3/16" (#1 MT).
LCENT4 MT #2 4-pc Drive Center Set ........................................$
LCENTLT1X MT #1 Live Center ..........................................................$ LCENTLT2X MT #2 Live Center ..........................................................$
44.95 19.95 19.95
keyless style
Page 1 |
Page 2 |
Page 3 |
Page 4 |
Page 5 |
Page 6 |
Page 7 |
Page 8 |
Page 9 |
Page 10 |
Page 11 |
Page 12 |
Page 13 |
Page 14 |
Page 15 |
Page 16 |
Page 17 |
Page 18 |
Page 19 |
Page 20 |
Page 21 |
Page 22 |
Page 23 |
Page 24 |
Page 25 |
Page 26 |
Page 27 |
Page 28 |
Page 29 |
Page 30 |
Page 31 |
Page 32 |
Page 33 |
Page 34 |
Page 35 |
Page 36 |
Page 37 |
Page 38 |
Page 39 |
Page 40 |
Page 41 |
Page 42 |
Page 43 |
Page 44 |
Page 45 |
Page 46 |
Page 47 |
Page 48 |
Page 49 |
Page 50 |
Page 51 |
Page 52 |
Page 53 |
Page 54 |
Page 55 |
Page 56 |
Page 57 |
Page 58 |
Page 59 |
Page 60 |
Page 61 |
Page 62 |
Page 63 |
Page 64 |
Page 65 |
Page 66 |
Page 67 |
Page 68 |
Page 69 |
Page 70 |
Page 71 |
Page 72 |
Page 73 |
Page 74 |
Page 75 |
Page 76 |
Page 77 |
Page 78 |
Page 79 |
Page 80 |
Page 81 |
Page 82 |
Page 83 |
Page 84 |
Page 85 |
Page 86 |
Page 87 |
Page 88
